AMMO CDC SET B 250 QUIZZES TEST
WITH COMPLETE SOLUTIONS
GRADED A+
QUESTIONS AND ANSWERS
Before using an electric drill, what is the first thing you should do?
a) make sure the diameter of the hole to be drilled is within the capacity of the drill
b) Connect the drill to the power source
c) ask a coworker for assistance
d) insert the chuck key. ANSWER -a) make sure the diameter of the hole to be drilled is
within the capacity of the drill
The purpose of cutting lubricant in most drilling operations to increase the
a) Life of the drill only
b) speed of drilling only
c) frictional heat during drilling
d) drilling speed and the drill bit life. ANSWER -d) drilling speed and the drill bit life
which minimum articles of safety gear must be worn when using a bench grinder?
a) apron and gloves
b) eye and face protection
c) gloves and steel-toed boots
d) safety glasses in long sleeved shirt. ANSWER -b) eye and face protection
an electric saw blade must be operating at what speed before it contacts the material being
cut?
a) full
b) low
c) moderate
d) accelerated. ANSWER -a) full
,how many pounds per square inch (psi) of clean, dry air is required at the tool end of the air
hose to ensure the tool is operating safely and efficientl?
a) 60
b) 90
c) 110
d) 125. ANSWER -b) 90
what condition would prevent an operator from applying power to a hoist or other powered
lifting device?
a) an AF Form 979 is attached to the unit
b) potential for lightning within 15 miles of the area
c) procedures are not covered in detail in the owners manual
d) The unit is tagged with a DD form 1574-1, condition code a. ANSWER -a) an AF Form
979 is attached to the unit
what should be worn any time there is a potential for injury from overhead objects during a
lifting operation?
a) kevlar
b) safety goggles
c) leather gloves
d) protective helmets. ANSWER -d) protective helmets
what is the most common type of lifting sling used in the munitions career field?
a) chain assembly
b) web strapping
c) metal mesh
d) wire rope. ANSWER -d) wire rope
The following are all good safety practices to follow when using a lifting sling except
a) standing clear of the attached load
b) padding any sharp corners the sling may come in contact with
c) keeping your hands and fingers from between the sling in the load
,d) inspecting the sling by passing your bare hand over the body of the sling. ANSWER -d)
inspecting the sling by passing your bare hand over the body of the sling
The annunciators displayed on the fluke 8025 - series multi meter are used to distinguish
among
a) ohms, milliohms, and kilohms
b) ohms, kilohms, and megohms
c) amps, ohms, and millivolts
d) ohms, volts, and amps. ANSWER -d) ohms, volts, and amps
what are the two operational modes of the fluke 8025 Dash series multimeter?
a) alternating current and direct current
b) range and hold
c) auto and manual
d) continuous and momentary. ANSWER -b) range and hold
The steering system on the MHU - 141/M trailer has a turning radius of how many inches?
a) 90
b) 200
c) 400
d) 600. ANSWER -b) 200
when the MHU - 141 trailer is loaded or towed with the hinged deck panels open, what
must be done?
a) The deck-panel supports must be properly positioned and locked in place with quick-
release pins
b) The deck-panel supports must be properly positioned and held in place with a tiedown
strap
c) bomb chocks must be positioned to the deck panels and locked in place with cotter pins
d) Close and lock the two deck panels; the trailer cannot be towed in this configuration.
ANSWER -a) The deck-panel supports must be properly positioned and locked in place
with quick-release pins
what is the maximum load capacity of the MHU - 110/M trailer?
, a) 5000 pounds
b) 5500 pounds
c) 15000 pounds
d) 20000 pounds. ANSWER -c) 15000 pounds
The parking brake on the MHU - 110/M is applied by
a) pulling either one of two hand levers located on each side of the front of trailer
b) pulling either one of two hand levers located on each side of the rear of trailer
c) pulling the center hand lever located in the front of trailer
d) pulling the surge brake located on the tongue of the trailer. ANSWER -a) pulling either
one of two hand levers is located on each side of the front of trailer
how many openings (hinged door panels) are on the deck of the MHU - 226 trailer?
a) one
b) two
c) three
d) four. ANSWER -c) three
what type of steering aids the MHU - 226 in a tighter steering radius?
a) rack and pinion
b) power recirculating ball
c) front-wheel automotive type
d) four-wheel double ackerman. ANSWER -d) four-wheel double ackerman
after 463L pallets are positioned on a rollerized trailer, what can you use to secure the
pallets to the trailer?
a) steel chains only
b) wire ropes and slack adjusters
c) wood bracing and tie down straps
d) MB-1 chain assemblies and/or tiedown straps. ANSWER -d) MB-1 chain assemblies
and/or tiedown straps
WITH COMPLETE SOLUTIONS
GRADED A+
QUESTIONS AND ANSWERS
Before using an electric drill, what is the first thing you should do?
a) make sure the diameter of the hole to be drilled is within the capacity of the drill
b) Connect the drill to the power source
c) ask a coworker for assistance
d) insert the chuck key. ANSWER -a) make sure the diameter of the hole to be drilled is
within the capacity of the drill
The purpose of cutting lubricant in most drilling operations to increase the
a) Life of the drill only
b) speed of drilling only
c) frictional heat during drilling
d) drilling speed and the drill bit life. ANSWER -d) drilling speed and the drill bit life
which minimum articles of safety gear must be worn when using a bench grinder?
a) apron and gloves
b) eye and face protection
c) gloves and steel-toed boots
d) safety glasses in long sleeved shirt. ANSWER -b) eye and face protection
an electric saw blade must be operating at what speed before it contacts the material being
cut?
a) full
b) low
c) moderate
d) accelerated. ANSWER -a) full
,how many pounds per square inch (psi) of clean, dry air is required at the tool end of the air
hose to ensure the tool is operating safely and efficientl?
a) 60
b) 90
c) 110
d) 125. ANSWER -b) 90
what condition would prevent an operator from applying power to a hoist or other powered
lifting device?
a) an AF Form 979 is attached to the unit
b) potential for lightning within 15 miles of the area
c) procedures are not covered in detail in the owners manual
d) The unit is tagged with a DD form 1574-1, condition code a. ANSWER -a) an AF Form
979 is attached to the unit
what should be worn any time there is a potential for injury from overhead objects during a
lifting operation?
a) kevlar
b) safety goggles
c) leather gloves
d) protective helmets. ANSWER -d) protective helmets
what is the most common type of lifting sling used in the munitions career field?
a) chain assembly
b) web strapping
c) metal mesh
d) wire rope. ANSWER -d) wire rope
The following are all good safety practices to follow when using a lifting sling except
a) standing clear of the attached load
b) padding any sharp corners the sling may come in contact with
c) keeping your hands and fingers from between the sling in the load
,d) inspecting the sling by passing your bare hand over the body of the sling. ANSWER -d)
inspecting the sling by passing your bare hand over the body of the sling
The annunciators displayed on the fluke 8025 - series multi meter are used to distinguish
among
a) ohms, milliohms, and kilohms
b) ohms, kilohms, and megohms
c) amps, ohms, and millivolts
d) ohms, volts, and amps. ANSWER -d) ohms, volts, and amps
what are the two operational modes of the fluke 8025 Dash series multimeter?
a) alternating current and direct current
b) range and hold
c) auto and manual
d) continuous and momentary. ANSWER -b) range and hold
The steering system on the MHU - 141/M trailer has a turning radius of how many inches?
a) 90
b) 200
c) 400
d) 600. ANSWER -b) 200
when the MHU - 141 trailer is loaded or towed with the hinged deck panels open, what
must be done?
a) The deck-panel supports must be properly positioned and locked in place with quick-
release pins
b) The deck-panel supports must be properly positioned and held in place with a tiedown
strap
c) bomb chocks must be positioned to the deck panels and locked in place with cotter pins
d) Close and lock the two deck panels; the trailer cannot be towed in this configuration.
ANSWER -a) The deck-panel supports must be properly positioned and locked in place
with quick-release pins
what is the maximum load capacity of the MHU - 110/M trailer?
, a) 5000 pounds
b) 5500 pounds
c) 15000 pounds
d) 20000 pounds. ANSWER -c) 15000 pounds
The parking brake on the MHU - 110/M is applied by
a) pulling either one of two hand levers located on each side of the front of trailer
b) pulling either one of two hand levers located on each side of the rear of trailer
c) pulling the center hand lever located in the front of trailer
d) pulling the surge brake located on the tongue of the trailer. ANSWER -a) pulling either
one of two hand levers is located on each side of the front of trailer
how many openings (hinged door panels) are on the deck of the MHU - 226 trailer?
a) one
b) two
c) three
d) four. ANSWER -c) three
what type of steering aids the MHU - 226 in a tighter steering radius?
a) rack and pinion
b) power recirculating ball
c) front-wheel automotive type
d) four-wheel double ackerman. ANSWER -d) four-wheel double ackerman
after 463L pallets are positioned on a rollerized trailer, what can you use to secure the
pallets to the trailer?
a) steel chains only
b) wire ropes and slack adjusters
c) wood bracing and tie down straps
d) MB-1 chain assemblies and/or tiedown straps. ANSWER -d) MB-1 chain assemblies
and/or tiedown straps
