Bestgrades2

At 0 PSIG, how many BTU are necessary to change 1 lb of water at 212 Degrees F into 1 lb of steam? - ANSWERS970 BTU Radiation is? - ANSWERSa form of heat transfer that is radiated or transmitted in the form of waves. Steam at 100 PSI and 400 Degrees F is? - ANSWERSsuperheated Which of the following most closely defines sensible heat? a) An established relationship comparing any substance to the heat content of water b) Heat quantity that can be felt or measured by a thermometer c)...

what are the conditions necessary for good combustion? a) low sulfur content b) Thermal, thermocoupler, tubular c) turbulence, temperature, time 3T's - ANSWERSc) turbulence, temperature, time 3T's why is secondary air necessary in hand fired boilers? a) Necessary to burn the combustible gases b) if primary air should fail c) used only if sulfur content is high - ANSWERSa) Necessary to burn the combustible gases when pressure increases on steam from a given amount of water wha...

What would be the correct term for a person possessing the appropriate qualifications, knowledge, skills & experience to supervise or perform work safely and in accordance with the act? -Trained -Competent -Signed-Off -Education - ANSWERS-Competent Unqualified individuals operating a power plant or pressure plant risk the ____ of the plant and the general public. -safety -health -economy -comfort - ANSWERS-safety According to the "Act" a person holding a "B" pressur...

Definitions such as shift engineer, chief power engineer, and assistant shift engineer are found in: - ANSWERSAlberta's Power Engineers Regulations Which of the following codes have the Canadian jurisdictions adopted in reference to pressure vessel regulation? - ANSWERSCSA B51 The Boilers and Pressure Vessels Regulation was put into place to protect: - ANSWERSThe public Which of the following is not a part of the Boiler and Pressure Vessel Acts across Canada? - ANSWERSThe regulation ...

What is a jurisdiction - ANSWERSCanada consists of 10 provinces and three territories. With these chapters, each of these is referred to as a jurisdiction rather than a province or territory. Each jurisdiction has his own legislation governing various aspects of power engineering. Explain the intent of the regulations governing the operation of boilers and pressure equipment - ANSWERSTo give the director or administrator of the department or branch of government a means of evolving within the...

An aquastat stops and starts a burner by sensing the ___ temperature. - ANSWERSBOILER WATER The number of blowdowns required for a boiler can be determined by ___. - ANSWERStesting the boiler water Oxygen in a boiler causes ___. - ANSWERSPITTING Impurities on the water surface in a steam and water drum are best removed by ___ blowdown. - ANSWERSSURFACE A modulating pressure control on a steam boiler is used to control the ___. - ANSWERShigh and low fire ranges A(n) ___ is a boiler...

Certificate of inspection. - ANSWERSmeans a sticker attached to the boiler or pressure vessel which documents the month and year of the inspection and the employer of the inspector performing the inspection. Certificate of registration - ANSWERSmeans a document that has been made available on the department's Web site that lists all registered boilers and pressure vessels at a location, including the last inspection date, the certificate expiration date, and the maximum allowable working...

A body formed in 1919 for the promotion of safety and uniformity in the construction, installation and inspection of boilers and pressure vessels was the: - ANSWERSNational Board of Boiler and Pressure Vessel Inspectors. The code that regulates mechanical refrigeration is: - ANSWERSCSA B-52 When a fitting is to be registered within a jurisdiction an application must be made to: - ANSWERSthe Chief Inspector. Before an inspector issues the first certificate of inspection for any boiler an...

What type of boiler is assembled piece by piece on site? A) Packaged boiler B) Field erected boiler C) Field assembled boiler D) Refrigerated boiler E) None of these answers is correct - ANSWERSb The term "heating plant" is defined in: 1. ASME Section I 2. ASME Section IV 3. CSA B-514. Provincial Power Engineers Regulation 5. Provincial Pressure Equipment Safety Regulation A) 1, 4 B) 1, 3 C) 1 D) 2, 4 E) 4, 5 - ANSWERSd Manholes are: A) ...

1. What is the acronym for The National Board of Boiler and Pressure Vessel Inspectors? a. CSA. b. ASME. c. NBA. d. NBBI. e. HSN. - ANSWERSd The Alberta Boilers Safety Association (ABSA) is responsible for the administration of the legislation for _____ and _____. a. Boilers, heaters. b. Exams, testing. c. Boilers, pressure vessels. d. Testing, fee collection. e. Inspections, process design. - ANSWERSc What designates the classification of the certificate of competency,...