Kamwarajoy7

Size 526 Exam #2 Questions and Correct Answers/ Latest Update / Already Graded Defined purpose Degree of similarity among members Rules Boundaries Content (what is said in the group) Process (underlying dynamics among group members) Ans: Characteristics that influence a group's progress and outcomes include (7): 1) human beings are social animals 2) we heal in community Ans: The two basic premises of group therapy are: group content Ans: All that is said in a gr...

Noise: In gear, clutch disengaged (pedal to floor) Ans: Pilot bushing or bearing Noise: Neutral, clutch disengaged (pedal to floor) Ans: Release bearing Noise: Neutral, clutch engaged (pedal up) Ans: Input shaft bearing Binding U-Joint will damage?? Ans: Extension housing bushing and seal What is used to check the clearance between the shift fork and the synchronizer sleeve? Ans: A feeler guage Warped pressure plates... Ans: ... should be replaced Ring and pinion ...

On a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad: A. Proportioning valve B. Pressure safety switch C. Metering valve D. Residual check valve Ans: The correct answer is C. The metering valve delays the flow of brake fluid to the front calipers until the pressure in the system rises to a point where the wheel cylinder can overcome the tension of the brake shoe returning spring. The purpose is ...

A drum is chattering on the brake lathe. This could be the result of: A. Failure to install the dampening belt. B. Cutting too slowly. C. Dull cutting blades. D. Cutting speed too fast. Ans: A A vehicle is equipped with a hydro-boost brake system has a hard pedal with little braking action. Which of the following could be the cause? A. Low brake fluid B. Air in the brake fluid C. Low power steering fluid D. An overtightened power steering belt Ans: C Which of the fol...

Camshaft ASE C1 Study Guide Questions and Terms Questions and Correct Answers/ Latest Update / Already Graded Ans: a rotating shaft within the engine that opens and closes the intake and exhaust valve in the engine. The cam is driven at half crank speed by the timing chain, timing belt, or timing gears connected to the crankshaft. Main Bearings and Caps Ans: Main bearings and caps attach the crankshaft to the block; they must be torqued to specification. Timing Gears Ans:...

Coolant should be tested for ________. Proper color Freezing point (temperature) Specific Gravity Both b and c Ans: Both b and c Two technicians are discussing a compression test. Technician A says that the engine should be cranked over with the pressure gauge installed for "4 puffs." Technician B says that the maximum difference between the highest reading cylinder and the lowest reading cylinder should be 20%. Which technician is correct? Technician A only Technici...

An air bag system is being serviced, Technician A says to disconnect the yellow SRS connectors at the front of the vehicle. Technician B says to disconnect and isolate the negative battery cable. Who is right? A. Technician A only B. Technician B only C. Both A and B D. Neither A or B Ans: .B Which of these should be used when soldering electrician wiring connections? A. rosin core flux B. acid core flux C. sulfur core flux D. none of the above Ans: .a When testi...

After a long drive red fluid is seen on the transmission case and under the chassis of a vehicle. Technician A says this can be caused by fluid aeration. Technician B says this could be caused by engine overheating. Who is correct? A. Technician A B. Technician B C. Both A and B D. Neither A or B Ans: C. Both A and B The MIL is illuminated and the transmission only operates in third and reverse gears. Which of the following is the MOST likely cause of this condition? A. Adap...

What is aircraft survivability Ans: The capability of an aircraft to avoid or withstand a man made hostile environment What three factors influence survivability Ans: Avoidance, susceptibility, vulnerability What is avoidance Ans: Suppressing air defense or operating outside the range or capabilities of threat weapons What is susceptibility? Ans: If a threat is unavoidable, minimizing the exposure to the weapon can reduce the chance of a successful engagement What is vu...

Technician observes that the brake fluid level is at the "Min" mark in the master cylinder reservoir. Tech A says that worn front pads could be the cause. Tech B says that a leak in the brake hydraulic system could be the cause. Who is right? Ans: Both A and B The tires of a vehicle are being rotated and balanced. Tech A says that the wheel weight retaining clips must be matched to the rim profile. Tech B says that directional tires are rotated in a criss-cross pattern. Who is...