Jackline98

d - ️️Large journal or sleeve bearings have grooves a) In the high pressure area of the bearing babbit b) Cut into the bearing housing c) For distributing lubricant evenly just after the pressure area d) In the non-pressure area c - ️️Using pressurized air to blow out a cleaned bearing a) Should only be done in well ventilated areas b) Must be done only when the bearing is hot c) Will cause the bearing to become pitted d) Should be done at an angle so the bearing can...

R4B When grease is used in an antifriction bearing after cleaning, the bearing housing should not be filled _____ full. Select one: a. more than 1/3 b. more than 1/2 c. more than 3/4 d. less than completely - ️️a R4B A large journal bearing which is running hotter than normal can be cooled by: Select one: a. Direct application of cool water b. Loosening the bearing caps c. Decreasing the viscosity of the oil by cooling it d. Pumping additional grease into it - ️️b R4B A colla...

d - ️️Pneumatic controllers are divided into two basic classes,: Choose one answer. a. Direct and reverse b. Off/on and proportional c. Positive and negative action d. Bleed and non-bleed e. Reset and gain d - ️️Prior to a worker entering the steam drum of an off-line boiler that is connected to a common, pressurized steam header, the

The best way to clean a bearing is: Select one: a. to send it to the manufacturer b. to acid clean it c. to first remove it from the machine d. to vacuum it - ️️c This number indicates the acidity of an oil: Select one: a. pH b. acidity c. alkalinity d. neutralization - ️️d This type of thrust bearing does not utilize an "oil wedge": Select one: a. Mitchell type b. collar type c. flotation type d. Kingsbury type - ️️b

When replacing or removing an antifriction ball bearing, the applied force should: Select one: a. only be applied to the press fit race b. always be against the inner race c. always be against the outer race d. be made only after heating the bearing - ️️a Whenever feasibly possible, when checking bearings on running pieces of equipment, it is wise to: Select one: a. check the oil quality leaving each bearing b. smell the normal odours of the running bearing c. get accustomed to nor...

Define: "Partial Birth Abortion" - ️️It is not an undue burden Define: 24-Hour Waiting Period - ️️States may require a 24-hour waiting period between the time of a woman's consent and the abortion - this is not an undue burden. True or False: Substantive Due Process is a concept used by the U.S. Supreme Court from about 1900 to 1937 to invalidate laws that tried to regulate safety conditions in the workplace -- essentially the Court would substitute its judgment for that of th...

Which of the following are the two major factors the Court uses in determining if a certain issue is a non-justiciable political question? - ️️(1) The textual constitutional commitment of the issue to a political branch (2) The lack of judicially discoverable and manageable standards. Which of the following best describes how the concept of a state's "quasi-sovereign interests" modifies the standing analysis in the view of the Court in Massachusetts v. EPA? - ️️A state can sat...

When can the T38 fly a Cat D approach? -️️Straight in approach flown Final approach is flown at 165 Kias or less Map is flown at 260 KTAS or less When circling for the T38, get proper displacement of ____ NM, and limit bank angle to _____. -️️1.5, 45 degrees of bank When circling for the T38, what airspeed and flap setting is needed? -️️Final turn airspeed Flaps 60 until on final Flaps 100 when on final Instrument penetrations are normally flown at ___ KCAS. -️️300 KCAS M...

When does the anti-ice system come on? - ️️placing the switch to manual on, loss of right AC with no cross, engine RPM below 65% What happens to takeoff distance as weight decreases? Why? - ️️decreases. Since takeoff speed is less and less distance is required to accelerate to a slower speed, takeoff distance is less. what happens to takeoff factor as temperature and pressure altitude increase? - ️️increases, takeoff factor is by definition based only on temperature, pressure alt a...

1. Compared to a straight wing, a swept wing will a. stall at a higher AOA b. have a higher C(L Max) c. have a more abrupt stall d. both a and c are correct - ️️a. 2. An increase in aircraft weight _______ the rate of climb a. increases b. decreases c. does not change - ️️b. 3. As an aircraft burns fuel and the gross weight decreases, the maximum range airspeed a. increases b. decreases c. remains the same - ️️b.

cash flow - ️️Cash that comes in and out of a business is called which of the following: Dealer to Dealer - ️️Gun values can vary from region to region and from which of the following: Direct Mail - ️️Which of the following includes brochures, letters, reply cards, price lists, catalogs, and coupons: Display Advertising - ️️A business owner should consider hiring an agency if the budget is large enough to include which of the following: Duty Weapon - ️️With sales to law e...

_____ must be tightly connected to prevent opening during concrete pouring. A. Soft spots B. Floor deck C. Concrete D. Side laps - ️️D. Side laps 41 _____ steel deck would have a designation of 3" x 8" (DR)? A. Roof B. Composite C. Form D. Cellular - ️️A. Roof

Which of the following is a tool made of hardened tool steel- hard enough to cut all but ultra hard alloys and cause hardened steel. These simple tools can be compared to the paint brushes of an artist. - ️️Gravers An engraved design on steel can be geometric- straight lines, triangles, circles, etc - or it can be: - ️️Artistic Before bluing, a gunsmith must make certain that all parts are thoroughly cleaned with which of the following: - ️️A Degreasing Solution Before handling an...

You may not be able to make a direct ascent to the surface without substantially increasing your risk of decompression sickness and your dive computer may require you to make a series of decompression stops - ️️What may happen if you go too deep or stay too long? Blender - ️️The person who creates the Nitrox used to fill scuba cylinders is referred to as a: Consult the Old Diver's Almanac. - ️️All of the following are ways to check for the availability of Nitrox at travel destin...

b. Fission - ️️________ is the process in which a large nucleus "splits" into two intermediate-size nuclei. b. Instantaneous Speed - ️️____________ of an object is its speed at that instant of time. b. Law of Conservation of Mass - ️️No detectable change in the total mass occurs during a chemical reaction Molecule - ️️is an electrically neutral particle composed of two or more atoms chemically bonded Motion - ️️If an object changes position, we say that _____ has oc...

Surface, under water - ️️If you and your buddy follow the same plan for dealing with buddy separation, you will end up meeting either on the _________ or ________ ___________. 1: Surface, dive boat 2: Shore, dive boat 3: Surface, under water 4: Boat, under water The weaker buddy. - ️️Which member of the buddy team determines the pace for the dive? 1: It doesn't matter, so long as both buddies agree. 2: The stronger buddy. 3: The weaker buddy. 4: None of the above. When attem...

__________ is an immediately life-threatening condition where every second counts in recognition and taking the victim to definitive care. Select one: DCS Narcosis GAS AGE - ️️AGE is an immediately life-threatening condition where every second counts in recognition and taking the victim to definitive care. Even the chance that what you observe in a diver might be an air embolism necessitates activating the emergency medical system and arranging a hasty transport. Despite the relaxing n...

Barrels - ️️Oil is measured in ___________. Streambank erosion - ️️____________: This is a problem in farmland streams, where soil washes away from streambanks. Subsidence - ️️This the gradual sinking of the ground surface. Sulfur Dioxide (So2) - ️️___________: This is a colorless, corrosive gas that damages both plants and animals. Sustainability - ️️A search for ecological stability and human progress that can last over the long term. Sustainable Agriculture - ️️__...

True - ️️The cleaning of the primer pocket cannot be done until the primer is removed. True - ️️The dent, coming from the firing pin striking the metal side of the primer, creates the pressure needed to ignite the priming mixture. True - ️️The Hornady concentricity tool is useful due to the ability to bump ammo but cannot help with troubleshooting. True - ️️The shellholder is specific not to caliber, but rather to the dimensions of the case head. True - ️️To achieve prope...