NURSING TEST

NCCER module 5 (construction drawings) Questions and Answers correct plans used for work that has to do with construction in or on the earth are called? civil plans the material to be used for walls would be found in the? structural plans what information in a drawings title block identifies the project? sheet title the information needed to identify lines and other symbols on a cunstruction drawing can be found in the? legend break lines are used to show that? ...

NCCER Module 9 (material handling) Questions and Answers before attempting to lift any materials? make sure the load does not have perusing nails wires or sharp edges before attempting to lower an overhead load? size up the load what is the proper procedure to lift objects bend knees and get a good grip, lift with legs keep back straight and head up when stacking bags of material that are the same width, step back and cross key the bags? every 10 bags high. neve...

Pipefitter NCCER Test Questions and Answers correct Convert 1/4 to its decimal equivalent. A) .01 B) .25 C) 0.4 D) 0.5 B Piping that is field-routed to a pump must be supported A) Off the pump suction B) Diagonally C) Independently D) Off the pump discharge C What is used when lighting a cutting torch ? A) Striker B) Cigarette lighter C) Match D) Any open flame A Where is specific information needed to install piping and associated items found ? A) Reliabili...

NCCER Module 6- Introduction to Construction Drawings Questions and Answers Most construction drawings today are​ hand-drawn by drafters. False The border is a clear area of about​ _____ inch(es) around the edge of the drawing. 1/2 The legend is the same as a company logo on a construction drawing. False A civil plan is also called​ a(n) _____ plan. plot The natural contours of the land are often shown on a civil plan. True A roof plan is likely ...

Electrical NCCER test Questions and Answers correct In a guardrail system, the guardrails can be made of any of the following EXCEPT: ropebanding If the potential across the circuit is 48 volts and the current is 5 amps the resistance of the circuit is: 9.6 ohms A UL listed rod type grounding electrode must have a minimum length of: 8' What is the MINIMUM number of overload sensing units required for all three phase motors? 3 In a circuit of pure capacitance, ...

Instrument tech nccer questions! Questions and Answers correct 1) When is the BEST time to document each loop check for commissioning ? A. Prior to the start of inspection B. When all test and inspection activities are complete C. When updating information on a daily basis D. At the time each test is completed D. At the time each test is completed (INST LVL4)(12410-16/ Section 3.2.0) 2) Teflon paste must not be used on : A. Nitrogen service B. Natural gas service C. Water service ...

NCCER Material Handling Study Guide Questions and Answers correct Before attempting to lift any material, _____. look for any protruding nails, wires, or sharp edges Before attempting to lower an overhead load, _____. size up the load What is the proper procedure to lift objects? Lift with your legs, keep your back straight, & keep your head up. When stacking bags of material that are the same width, step back & cross the bags _____. every 10 bags high Never stac...

Module 2- NCCER Introduction to Construction Math Test Questions and Answers correct ten thousands What is the place value of 7 in the number 576,312? 36,211 Thirty-six thousands, two hundred eleven pipe fittings have been ordered how would you write this in a whole number using digits? 1,235 Add the following numbers together 413, 718, 94, and 10. The sum is $1,050.00 You receive $30.00 an hour as a pipe fitters working 40 hours a week. The taxes withheld from your pay...

NCCER Exam Review 33301 Questions and Answers correct A major benefit of using the cloud is a? Lower risk of data loss One method used to shorten IP version 6 addresses is? Zero suppression Which of the following is a set of instructions that clearly defines how a computer handles all input and output operations? Basic input/output systems(BIOS) What method is used to provide power to newly installed PoE devices? Switch Method The IP portion of TCP/IP provides? ...

NCCER Module 8 (employability skills) Questions and Answers correct a companies documented philosophy is called its? mission statement the time to learn about a potential employer is? before an application is ever submitted when preparing a resume, you should? format your resume chronologically during a job search, it is good practice to? look for a job that will match your skill level before employment begins, candidates for construction jobs most often? have a...

Power tools NCCER Questions and Answers correct what does pneumatic mean? Air power What kind of power does a porta power use? Hydraulic power The most common use of the power drill is to what? Make holes in wood, metal, and plastic Hammer drills are designed to drill into what? Concrete, brick, and tile The electromagnetic drill is a what? Portable drill used on thick metal When cutting with a circular saw grip the saw handles________? Firmly with to ha...

Chapter 1 Core Curriculum NCCER Questions and Answers correct 1.0.0-Companies with strong safety culture have fewer at-risk behaviors, lower incident and accident rates, less turnover, lower absenteeism, and higher productivity. 1.0.0- What is a true statement regarding safety? Safety is a learned behavior and attitude. 1.2.8- Poor lighting, excessive noise, and inadequate guards for moving parts are examples of what? Unsafe Conditions. Other examples of unsafe conditions are a...

NCCER STUDY GUIDE Questions and Answers correct 1. Which organization requires a person to be trained in order to operate personal lifting equipment? OSHA 1. Where would the usage of a RTJ Gasket be found? High Pressure System All of the following are examples of internal man way hardware except Slide Fastener 1. What type of wrench measures how much a fastener is being tightened? Torque 1. The fitting that makes it easy to disassemble threaded piping is Union ...

NCCER Material Handling Study Guide Questions and Answers Before attempting to lift any material, _____. look for any protruding nails, wires, or sharp edges Before attempting to lower an overhead load, _____. size up the load What is the proper procedure to lift objects? Lift with your legs, keep your back straight, & keep your head up. When stacking bags of material that are the same width, step back & cross the bags _____. every 10 bags high Never stack or st...

NCCER Test Practice Questions and Answers correct Ropebanding In a guardrail system, the guardrails can be made of any of the following EXCEPT: a) pipe b) chain c) ropebanding d) cable 9..6 ohms If the potential across the circuit is 48 volts and the current is 5 amps the resistance of the circuit is: a) 4.8 ohms b) 9.6 ohms c) 48.0 ohms d) 96.0 ohms 8' A UL listed rod type grounding electrode must have a MINIMUM length of: a) 6' b) 8' c) 10' d) 20' ...

NCCER Exam 1 Questions and Answers correct Companies with strong safety cultures usually have lower _____. a. turnover Which of these is a true statement regarding safety? a. Safety is a learned behavior and attitude. Poor lighting, excessive noise, and inadequate guards for moving parts are examples of _____. b. unsafe conditions The activity that consists of breaking a job into its component tasks and then analyzing each step for potential hazards is called a _____. a...

Nccer exam study guide Questions and Answers correct safety culture The culture created when the whole company sees the value of a safe work environment. OSHA Occupational Safety and Health Administration incident an unplanned event that may or may not result in property damage accident an unplanned event that results in personal injury and/or property damage fatal four Falls, Struck by, Caught between, and Electrical risk a measure of the probability, c...

Exam (elaborations) API 570 ASME SECTION V Combined Questions and Answers correct Exam (elaborations) API RP 574 4 Piping Components Questions and Answers correct Exam (elaborations) API 570 Practice Test Questions and Answers correct Exam (elaborations) API RP 574 11 Pressure Tests Questions and Answers Exam (elaborations) API 574 for API

API RP 574 4 Piping Components Questions and Answers correct 4.1 Piping 4.1.1 General Piping can be made from any material that can be rolled and welded, cast, or drawn through dies to form a tubular section. The two most common carbon steel piping materials used in the petrochemical industry are ASTM A53/A53M and ASTM A106. The industry uses both seamless and electric resistance welded (ERW) piping for process services, depending upon current economics and the potential for accelerate...

API 570 Practice Test Questions and Answers correct Document any systems containing tell-tale holes. The practice of installing guage holes (tell-tale holes) has been discontinued with the advent of current thickness measuring techniques. What action should the inspector take should he or she encounter piping systems that contain guage holes? 0.200" (AVG) The following thickness measurements were obtained at one examination point in a CML; 0.198", 0.200", 0.195", and 0.205...