Amazinggrace

The USPA Basic Safety requirements state that container opening for C-licensed skydivers must occur by _____________ unless waivered to a minimum altitude of _____________: A) 2,000 feet AGL, 1,500 feet AGL B) 2,500 feet AGL, 2,000 feet AGL C) 3,000 feet AGL, 2,500 feet AGL D) 4,000 feet AGL, 3,500 feet AGL - B) 2,500 feet AGL, 2,000 feet AGL A USPA C-license holder who has not made a freefall within the preceding six months should: A) attend a complete first-jump course B) make at least...

1) What is the primary directional control when moving forward to dock in freefall? a) arms b) legs c) shoulders - b) legs 2) What is the minimum break-off altitude for freefall in groups of five or fewer? a) 1,500 feet above planned deployment altitude b) 2,000 feet above planned deployment altitude c) 1,000 feet above planned deployment altitude - a) 1,500 feet above planned deployment altitude 3) What is the danger of entering a toggle turn too quickly? a) stall b) line twist c) li...

1) What happens to a jumper's fall rate when performing rolls, loops, or other freeflying maneuvers? a) Increases. b) Decreases. c) Stays the same. - a) Increases. 2) What happens to a visual altimeter when it's in the jumper's burble? a) Reads unreliably. b) Nothing. c) Reads high. - a) Reads unreliably. 3) What is the best way to recover from a stall to full glide? a) Quickly counteract with toggle input. b) Pull legs up into a tight ball. c) Smoothly raise the controls. - c) Smo...

What is the first priority of your pull priorities? - Pull-you must deploy the parachute What is the second priority of your pull priorities? - Pull at the proper altitude What is the third priority of your pull priorities? - Pull at proper altitude when stable You should check your altitude every time you... (3 things) - All are correct (5 seconds have passed, you complete a task, encounter difficulty) What is the first priority of your landing priorities? - Land with the wing level What ...

What is the first priority of your pull priorities? - Pull-you must deploy the parachute What is the second priority of your pull priorities? - Pull at the proper altitude What is the third priority of your pull priorities? - Pull at proper altitude when stable You should check your altitude every time you... (3 things) - All are correct (5 seconds have passed, you complete a task, encounter difficulty) What is the first priority of your landing priorities? - Land with the wing level What ...

Describe how to avoid the propeller(s) when approaching an aircraft. + - Approach fixed-wing aircraft from the rear. Who is responsible for seat belt use in the aircraft? + - pilot and jumper When must seat belts be fastened? + - movement on the surface (taxi), takeoff, and landing From whom do you take direction in the event of an aircraft problem? + - my instructor Why is it important to exit on "Go!"? - AFF and tandem students: helps student and instructors to leave at the same time a...

describe how to avoid the propeller(s) when approaching an aircraft - approach fixed-wing aircraft from the rear who is responsible for seat belt use in the aircraft - the pilot and each jumper when must deatbelts be fastened - during movement on the surface (taxi), takeoff, and landing from who do you take directions in the event of an aircraft problem - my instructor why is it important to exit on Go (or arch) - AFF and tandem students helps student and instructors to leave at the same t...

What is the recommended minimum breakoff altitude for free fall groups of five or fewer? - 1,500 feet above the highest planned deployment altitude What is the danger of entering a toggle turn too quickly? - line twist How can you avoid the propeller(s) while approaching an airplane? - approach only from the rear and behind the wing What is the biggest danger of a hard toggle turn near the ground? - 1) Line twist 2) Hard landing while still in a turn 3) Collision with other jumpers Wha...

A contractor wants to raise the car speed from 100 fpm to 125 fpm, it currently has a 12" sheave. What is required? - 100 fpm/125 fpm= 12"/ X =15 A MOV (Metal Oxide Varistor) burns out. You replace it, but cannot read voltage or resistance. What should you do? - Replace it with a larger MOV - 630 On a Ward-Leonard circuit the brake is set, but the motor is trying to slip through the brake. What is the issue? - Suicide Circuit - 425 You have an old DC motor and are adding an SCR drive, wh...

Which of the following is a term used to describe a body harness used in conjunction with a shock absorbing lanyard? - Personal fall arrest system A mechanic is working on a construction job, and finds the carpenter using a powder activated tool to anchor wall track. Of the following, which precaution should the mechanic take? - Wear hearing protection Which is the best way to communicate with your coworkers while you are in the machine room and they are working in the pit? - Two-way radio...

Ladder must be installed if pit is deeper than... - 35" (3') ASME A 17.1 - 2004 2.2.4.2 Ladder shall not extend more than ___ above the sill. - 48" (4') ASME A 17.1 - 2004 2.2.4.2 Rungs (cleats or steps) of ladder should be a minimum of ___ wide. - 16" ASME A 17.1 - 2004 2.2.4.2 Siderails shall have a clear distance of not less than ___ from their centerline to the nearest permanent object. - 4.5" ASME A 17.1 - 2004 2.2.4.2 Ladder access shall not be permitted if pit is deeper than __...

In a modernization they plan on moving the controller 30 feet away which ends up resulting in a voltage drop. What do you do? A) Call electric company for a step-up transformer, B) Use a bigger wire. - B) Use a bigger wire. Governor trips at 115% of rated speed, the over speed switch trips at 90% of the 115%. - If you are cutting something with a power saw, which way does piece you are cutting face. Up or down? - Down. They give you a voltage of 480 on primary and 216 on secondary and a c...

** An MOV burns out, you replace it but cannot read voltage or resistance. What should you do? - Replace it with a larger one (630) * On a Ward-Leonard circuit, the brake is set but the motor is trying to slip through the brake. What circuit is the issue? - Suicide circuit (425) ** A Hydro runs up with no load but does not run up with a full load. What is the issue? - The relief valve is set too low (805) ** Runby for a 1:1 car hits the CWT buffer 4" below the top landing. The CWT runby s...

Car running up keep stopping why? - Contact is not deenergizing in push button Third-floor bulbs burn out why? - Shorted resistor Car will not travel to second floor without a third-floor me a call and will not go down from three without a second-floor hall, what's the problem? - 2Fl 4/6 Why won't motor start? - MOL1 95/96 Car doors closed and won't run what do you check? - Check for voltage at four and five Bad Transistor Top barricade can be replaced with? - 1/4" Cable There is vol...

A Latching relay: Used for call registration,direction selection or as selector relays Two types are: Set/Rest are electrical and Mechanical Latching relays Need to know latching relay symbol, Its a box with shaded triangle in lower right hand corner. - Which relay do you need to Order 710 Pg, 7 RPM = 60 ∙ ƒ ÷ P÷2 = Step 1. 60 x Frequency (Hz.) = Step 2. Poles ÷ 2 = Take answer 1 and ÷ by answer 2 = - Know the formula for RPM 435 Pg. 5 If you are referring to a megohm meter, it ...

A contractor wants to raise the car speed from 100fpm to 125fpm, it currently has a 12" sheave. What sheave is required? - Diam=12" 12/4=3" 25fpm=3" 100fpm + 25fpm= 12"+3"= 15" sheave A MOV (Metal Oxide Varistor) burns out. You replace it, but cannot read voltage or resistance. What should you do? - Replace it with a larger MOV On a Ward-Leonard circuit the break is set, but the motor is trying to slip through the break. What is the issue? - Suicide Circuit You have an old DC motor ...

What is the recommended distance between ceiling mounted speakers in a hallway with heavy traffic? A. 2.4 m (8 ft) B. 3.7 m (12 ft) C. 4.9 m (16 ft) D. 6 m (20 ft) - A. 2.4 m (8 ft) A space has all hard surfaces including architecture and furnishings. The audio programming produced from the distributed sound system has become unintelligible. Which of the following will NOT mitigate the problem? A. Add tapestries to the walls. B. Provide additional speakers at lower output. C. Increase ...

If the input signal power to a communication system is 1 W and the output power is 1 mW, the system attenuation is: A. 3 dB B. 20 dB C. 30 dB D. 40 dB E. 1000 dB - C. 30 dB The signal at the input to a balanced twisted pair cable is 10 mW. The cable is 1000 feet long and has an attenuation of 1 dB per 100 feet. This cable is connected to the input of a receiver. The noise level at the input to the receiver is 1 microwatt. What is the signal-to- noise ratio (SNR) (dB) at the receiver inp...

Which of these cables is considered immune to electromagnetic interference? A) Optical Fiber B) Balanced Twisted-Pair C) Coaxial - A) Optical Fiber Reference: TDMM, 14th edition, page 2-37 Which of the following terms describes the transmission of signals in both directions at the same time? A) Simplex B) Half-duplex C) Full duplex - C) Full Duplex TDMM, 14th edition, page 1-39 Which of the following terms refers to signal interference between cable pairs? A) Crosstalk B) Impedance ...

C ----If the input signal power to a communication system is 1 W and the output power is 1 mW, the system attenuation is: A. 3 dB B. 20 dB C. 30 dB D. 40 dB E. 1000 dB B ----The signal at the input to a balanced twisted pair cable is 10 mW. The cable is 1000 feet long and has an attenuation of 1 dB per 100 feet. This cable is connected to the input of a receiver. The noise level at the input to the receiver is 1 microwatt. What is the signal-to- noise ratio (SNR) (dB) at the receiver i...