GPM Study guides, Class notes & Summaries

What type of o-ring is the most resistant to petroleum products - Buna-S What do you prime an FOP with? - Water What material are used for strainers? - Stainless steel or monel In a compressed air system, what causes the o-rings to fail to quickly? - Heat What do you use to measure resistance of a wire cover? - Meghometer Gallons per minute for a p-100 pump? - 100 GPM at 83 PSI with a 20 foot suction lift Starting over to enter a discrepancy to almis? - Add Maintenance Record What contami...

Becc test 3 Questions and Correct Answers, Complete Solution. 100% Correct. What is standard length (in feet) of a navy fire hose? 50 ft What gallon per minute (GPM) vari-nozzle is used with an in-line eductor? 95 GPM What is the standard length of the standard navy fire hose? 50 ft On a fire hose hose station the hose shall be stored at least __________ inches off the deck. 6 inches What is the name of the shroud at the end of the vari-nozzle? Pattern selector What size firehose is u...

Which is a characteristic of smooth bore nozzles? A. Prone to clogging with debris B. Cannot be used to apply compressed air foam C. Cannot be adjusted to different stream patterns D. Operate at higher nozzle pressures than fog nozzles - correct answer C. Cannot be adjusted to different stream patterns How is the rate of discharge for a manually adjustable fog nozzle changed? A. Pushing the bale forward or backward slowly B. Rotating the nozzle tip to choose a wider or narrower pa...

Texas Irrigator Practice Test Section 2 A properly designed irrigation system can: a). Save water, time, and money b). Save installation time c). Cost more d). Last longer a). Save water, time, and money When calculating the available water capacity of an irrigation site, irrigators refer to that amount in: a). Precipitation rates b). Infiltration rates c). GPM d). GPH c). GPM When using drip irrigation, the water volume of individual drip emitters is generally expressed in:...

You are the operator for a pool which is 164 feet long and 80 feet wide. The pool bottom has a constant slope which is 4 feet deep at the shallow end, and 10 feet deep at the deep end. What is the volume of this pool in gallons? - CORRECT ANS f You operate a pool which uses high rate sand filters. You discover that your filter tank has developed a major leak and must be replaced. Your pool operates with a flow rate of 525 GPM. Using a filter media rate (fmr) of 15 gallons per minute, what ...

Firefighter 1 Final Test Questions and Answers Latest Updated 2023/2024 (100% Verified). Which type of heat transfer is a major contributor to flashover? A. Nuclear B. Radiation C. Conduction D. Convection - answerD. Convection Which of the following IS NOT one of the methods by which water tenders unload? A. Jet dumps to increase flow rate B. Jet siphons to increase flow rate C. Gravity dumping through large dump valves D. Apparatus-mounted pumps that off-load the water - answerB. Jet ...

Firefighter 1 Final Test Questions and Answers Latest Updated 2024 (100% Verified). Which of the following IS NOT one of the methods by which water tenders unload? A. Jet dumps to increase flow rate B. Jet siphons to increase flow rate C. Gravity dumping through large dump valves D. Apparatus-mounted pumps that off-load the water - answerB. Jet siphons to increase flow rate Slab doors are constructed in two configurations: A. ledge and framed B. slab and panel C. raised and flat D. soli...

Fire Inspector 2: Combined Fire protection engineers have established _____ PSI as a minimum required residual pressure when computing the available water for flow test results. - 20psi The most common gallonage rating for horizontal shaft pumps in use today are _____ - _____ GPM. - 500 - 1500 gpm A fire pump serving a standpipe system should be tested ______ - weekly A fire department pumper can effectively supply around ______ feet in a high rise building depending on hydrant pr...

Firefighter 1 Practice Questions and Answers (101 Questions) Latest 2023/2024 | 100% Verified. A load the engineer planned for, or anticipated, in the building design is the definition of a(n) __________ load. A. dead B. concentrated C. impact D. design - Ans-D. design 4. A PRIMARY safety concern when raising a ladder should be: A. teamwork and strength B. ladder selection C. ladder placement and angle of inclination D. possible contact with electrical wires and overhead obstructions -...

Which of the following is NOT a responsibility of the fire apparatus driver/operator? (7) A. Detailed maintenance procedures B. Operating the apparatus properly, swiftly, and safely C. Ensuring that the apparatus and the equipment it carries are ready at all times D. Safely transporting firefighters, apparatus, and equipment to and from the scene of an emergency or other call for service - A. Detailed maintenance procedures Which of the following is NOT a basis for promotion to drive...