Examverse

What is the role of the Engineering Department Organization and Regulations Manual (EDORM)? - ANSWER ☑☑Governing directive for the Engineering Department Who must read the EDORM? - ANSWER ☑☑ALL PERSONNEL prior to assuming responsibilities in their department What are the engineering duties of the CO? - ANSWER ☑☑Responsible for the safe and proper supervision, operation, and maintenance of the engineering plant What are the engineering duties of the XO? - ANSWER ☑☑Des...

What does the this compartment number indicate 3-202-0-L? - ANSWER ☑☑3 - Deck number 202 - Forward most frame 0 - Position in relation to the centerline L - Compartment use What is the primary DC circuit? - ANSWER ☑☑2JZ What are the components of the fire tetrahedron? - ANSWER ☑☑- fuel - heat - oxygen - chemical reaction Who is the attack team leader? - ANSWER ☑☑Anyone (nozzlemen, hosemen, or plugmen) that's apart of the attack team How long does an indi...

What does EDORM stand for? - ANSWER ☑☑Engineering Departmental Organization and Regulations Manual What is the purpose of EDORM? - ANSWER ☑☑- It is the governing directive for the organization and basic operation of engineering department -provides guidance for the safe and effective operation of the Engineering Department What does EOSS stand for? - ANSWER ☑☑Engineering Operational Sequencing System What is the purpose of EOSS? - ANSWER ☑☑provide watch standers w...

Utility-owned low-voltage communication, radio and television coaxial cables may pass directly over a pool if at a minimum height of _____. a)18ft b)14ft c)16ft d)10ft - ANSWER ☑☑d) Communication, radio and television coaxial cables within the scope of Articles 800-820, shall be permitted at a height of not less than 10 feet above swimming and wading pools, diving structures and observation stands, towers or platforms. NEC Section 680.8(B). A typical wet-niche fixture must be instal...

1. Takeoffs of conduit are categorized into ______. - ANSWER ☑☑Power distribution, branch lighting, and branch power 2. Raceways are taken off per _____. Fittings required to make turns and extensions are taking off per _____. - ANSWER ☑☑Linear foot, each 3. All wires and conductors are taken off per _____. - ANSWER ☑☑Linear foot 4. All fittings, devices and boxes are taken off per _____. - ANSWER ☑☑Each Item 5. Permits and fees for tie-ins may be listed at lump s...

Parts to a Statement of Financial Position - ANSWER ☑☑Covers total assets, equities and liabilities ASSETS (A) 1. Non-current (revaluation) (not easily converted to cash within a year) 2. Current (inventories, cash, trade receivables, short term investments, pre-paid expenses) = Total assets (A) EQUITY AND LIABILITES (B) 1. Equity (share capital, reserves, retained earnings) =Total equity 3. Non-current liabilities (long-term borrowings/provisions) 4. Current liabilities (trade...

Peck and Hale gear is used most commonly for securing - ANSWER ☑☑automobiles Tonnage tax is officially based upon the figures obtained from the - ANSWER ☑☑Admeasurement Certificate What is the meaning of the term tare weight? - ANSWER ☑☑Weight of a container A long ton is - ANSWER ☑☑2,240 pounds Displacement refers to the - ANSWER ☑☑number of long tons of water displaced by a vessel afloat Stress on the topping lift of a swinging boom can be reduced by. - ...

To determine the potential for sales of coffee, as opposed to a specific brand, in a particular market area, a company should use the - ANSWER ☑☑category development index After calculating both the brand development index (BDI) and the category development index (CDI), a media planner obtains the following results: high BDI and low CDI. Which of the following information can be deduced from this data? - ANSWER ☑☑good market to advertise in but requires sales decline monitoring W...

How are residential furnance blower motors classified? - ANSWER ☑☑C. By starting method What is the first thing you should do before removing a contactor? - ANSWER ☑☑C. Disconnect the power supply A junction box used for joining wires mean be made of - ANSWER ☑☑D. All of the above Porcelain Metal Plastic What is the purpose of Heat anticipator in a furnace - ANSWER ☑☑C. Assists in controlling temperature. A cable contains a black wire a white wire and a small...

What is the correct type of seam for a grease stop? Pittsburgh lock S cleat welded continuously on outside spot welded on inside - ANSWER ☑☑welded continuously on outside Type-B vents are recommended for: incinerators combination gas-oil appliances appliances convertible to solid fuel standard gas-fired furnaces - ANSWER ☑☑standard gas-fired furnaces Cranes with a boom longer than 60 ft or with a rating greater than _____ require a boom-angle indicator. 5 tons 10 ...

Cable contains a black wire, white wire, and smaller uncoated copper wire. What to do with copper wire? - ANSWER ☑☑Ground it Needle on volt meter shows infinite ohms. What does this indicate? - ANSWER ☑☑Switch or circuit is open Difference between a gravity-type heating system and forced air is that the gravity type relies on _______________ for air distribution - ANSWER ☑☑Difference between hot and cold air What is the most efficient propane flame - ANSWER ☑☑soft bl...

If unused mortar stiffens due to hydration of cement, what must you do? - ANSWER ☑☑Discard the mortar What minimum time must you wait before caulking or grouting new tiles? - ANSWER ☑☑24-48 Hours How long should you wait before installing tile on a shower pan? - ANSWER ☑☑24 Hours Unstable dry rock, angular gravel, sandy loam, and cohesive soils having compressive strengths greater than 0.5 and less than 1.5 tons/sq ft (tsf), are typical examples of: - ANSWER ☑☑Type-B...

If unused mortar stiffens due to hydration of cement, what must you do? - ANSWER ☑☑Discard the mortar What minimum time must you wait before caulking or grouting new tiles? - ANSWER ☑☑24-48 Hours How long should you wait before installing tile on a shower pan? - ANSWER ☑☑24 Hours Unstable dry rock, angular gravel, sandy loam, and cohesive soils having compressive strengths greater than 0.5 and less than 1.5 tons/sq ft (tsf), are typical examples of: - ANSWER ☑☑Type-B...

A ladder should extend a minimum of _____ above the top of a trench or excavation. - ANSWER ☑☑1' According to OSHA, shoring lumber shall be ____. - ANSWER ☑☑Select structural cal/OSHA inspectors cannot, under most circumstances: - ANSWER ☑☑Enter a business outside of normal business hours. Every employer is required to post Material Safety Data Sheets: - ANSWER ☑☑on each job site Handrails must be installed on all open side of a scaffold if workers are subject to...

A subcontractor or material supplier has _____ days to file a lien once a notice of completion has been recorded. - ANSWER ☑☑30 How must a client submit a claim for service or repair of a defect on fit and finish items after a remodel? - ANSWER ☑☑By certified mail By overnight mail By personal delivery A contractor meets Mr. Jones at his home to discuss remodeling. The contractor and Mr. Jones sign a contract that includes a three-day cancellation form. After the contract...

The lifting lines should be as vertical as possible - ANSWER ☑☑When using a crane to lift a 12,000-gallon tank out of the excavation, what is the preferable position of the rigging lines attached to the tank's lifting eyes? A. One lifting line should be horizontal B. The lifting lines should be as far apart as possibles C. The lifting lines should be as horizontal as possible D. The lifting lines should be as vertical as possible Material that contains more than 1% asbestos - AN...

What is the minimum height of barricade in place around an open wellway? - ANSWER ☑☑42 inches What is the maximum angle of inclination for moving walks? - ANSWER ☑☑12 degrees What is the major advantage of a hydraulic elevator? - ANSWER ☑☑Requires less building structural support If all other elements in a hydro elevator remain the same, what would be the effect of increasing the size of the oil line? - ANSWER ☑☑Rate of flow is reduced What tool is used to check a...

The total weight of your elevator (force) is 8100 lbs. and its plunger area is 50 square inches. What is the system pressure? - ANSWER ☑☑162 psi Refer to the NEIEP Moving Walk Final Layout. What is the correct wellway-to-wellway distance? - ANSWER ☑☑134' 11" Electrolysis is caused by which of the following? - ANSWER ☑☑Stray current corrosion and Galvanic corrosion BOTH ARE CORRECT When using wire rope, the diameter of the sheaves must be how many times the diameter of t...

Hydro elevators in low rise applications do not need an _____ _____ room. - ANSWER ☑☑overhead machine Some advantages of hydros are lower equipment and building construction costs because the load of a hydro is carried to the _____ where as the load of a traction car is carried by the _____ _____. - ANSWER ☑☑ground, building structure When drilling the jack hole, the only proper way to determine if the hole is plumb is to remove the drill stem and bit and use a _____ _____. - AN...

HVAC CERTIFICATION EXAM 2024 WITH 100% ACCURATE SOLUTIONS Propane and Butane are _______ than air: - correct answer Heavier What will be the resistance in the circuit if the supply voltage is 30V and current flowing through the circuit is 5A - correct answer 6 ohms Temperature at which oil starts to produce a waxy substance that may interfere with the refrigeration system - correct answer Floc point What manifold gauge set is used to charge, evacuate, add oil and recover refrigeran...