Intermodal Dry Cargo CNTR/CSC Reinspection (Cert),
INTERMODAL DRY CARGO CNTR/CSC REINSPEC || A+
Guaranteed.
What is the primary reference used by inspectors to conduct CSC container inspections?
correct answers MIL-STD-3037
Which of the following containers allows for easier loading and unloading of large bulky
stock, such as bombs? correct answers Side-Opening
Which container component is highlighted? correct answers Threshold Plate
Which container component is highlighted? correct answers Top End Rail
Which container component is highlighted? correct answers Forklift Pockets
Which container component is highlighted? correct answers Gooseneck tunnel
What must be displayed on both ends, both sides, and the top of a container? correct answers
ISO Identification Markings
When inspecting containers, what tool would you use to inspect a container's alignment?
correct answers Measuring Tape
When inspecting containers, what tool is used to determine weld serviceability and the
severity of corrosion? correct answers Welder's Hammer
When inspecting containers, what tool is used to move containers by lifting them at the
corner fittings? correct answers Container handler
Where do you find the container inspection checklist for a mobile facility? correct answers
MIL-STD-3037, Appendix A
Which statement is true? correct answers MIL-STD-3037 has separate paragraphs that
document IMDG and non-IMDG criteria.
What is the maximum allowable depth of a door header dent? Refer to MIL-STD-3037,
Section 4 as required. correct answers ¾" for IMDG, 1-⅜" for general cargo
Select the appropriate defect classification for the following container defect: Dent 3/16"
deep on the road side panel.
Refer to MIL-STD-3037, Section 4 as required. correct answers Minor
Refer to DA Form 2404 below. What is the appropriate entry for Item #5 in this example?
correct answers Unserviceable for IMDG and Non-IDMG
According to the DD Form 2282 decal shown below, when was this container last inspected?
correct answers May 2018
INTERMODAL DRY CARGO CNTR/CSC REINSPEC || A+
Guaranteed.
What is the primary reference used by inspectors to conduct CSC container inspections?
correct answers MIL-STD-3037
Which of the following containers allows for easier loading and unloading of large bulky
stock, such as bombs? correct answers Side-Opening
Which container component is highlighted? correct answers Threshold Plate
Which container component is highlighted? correct answers Top End Rail
Which container component is highlighted? correct answers Forklift Pockets
Which container component is highlighted? correct answers Gooseneck tunnel
What must be displayed on both ends, both sides, and the top of a container? correct answers
ISO Identification Markings
When inspecting containers, what tool would you use to inspect a container's alignment?
correct answers Measuring Tape
When inspecting containers, what tool is used to determine weld serviceability and the
severity of corrosion? correct answers Welder's Hammer
When inspecting containers, what tool is used to move containers by lifting them at the
corner fittings? correct answers Container handler
Where do you find the container inspection checklist for a mobile facility? correct answers
MIL-STD-3037, Appendix A
Which statement is true? correct answers MIL-STD-3037 has separate paragraphs that
document IMDG and non-IMDG criteria.
What is the maximum allowable depth of a door header dent? Refer to MIL-STD-3037,
Section 4 as required. correct answers ¾" for IMDG, 1-⅜" for general cargo
Select the appropriate defect classification for the following container defect: Dent 3/16"
deep on the road side panel.
Refer to MIL-STD-3037, Section 4 as required. correct answers Minor
Refer to DA Form 2404 below. What is the appropriate entry for Item #5 in this example?
correct answers Unserviceable for IMDG and Non-IDMG
According to the DD Form 2282 decal shown below, when was this container last inspected?
correct answers May 2018
