NEIEP 200 Final Review Clear Questions to Pass
Save
Students also studied
NEIEP 200 Final EXAM COMPREHE... NEIEP 200 Final Review Relias Dysrhythmia Interpretation NE
Teacher 108 terms 73 terms 36 terms 58
Georges20_ Preview annablake128 Preview sunnydaisy48 Preview
Practice questions for this set
Learn 1 /7 Study with Learn
How are the ends of rails made so they may be joined together?
Choose an answer
1 The ends are riveted together 2 The ends are welded together
3 The ends are bolted together 4 The ends have a tongue and groove
Don't know?
Terms in this set (73)
Which lay of wire rope has the strand Regular Lay
wires in line with the rope axis?
At what speed should the counterweight Up to 10% higher than the car governor
safeties be set to trip?
Which type of safety uses an oil buffer Type C
between the car and safety planks?
What is the purpose of the terminal slow down and stop the car automatically at or near the top or bottom landing
motion switch?
If you have a 3500 lb. car rated at 4000 5100 lbs.
lbs. capacity, how much should the
counterweight assembly weigh for a
normal 40% installation?
, When the pit directional limit switch is Up
actuated, the normal circuits will allow the
car to run
_______should not be disassembled in the Oil Buffers
field.
The loss of traction between the hoist The elevator car being pulled into the over head.
ropes and the machine driver when the
counterweight lands on its buffer avoids...
Refer to Table 1. With a safety factor of 5, 52,000 lbs.
what is the breaking strength for 1 1/8"
nylon rope?
Which of the following applies to rope Prevent manila rope from unraveling by using whipping.
usage?
What does the designation 3/8" 6 X 30 It is a high strength cable with 6 strands composed of 30 wires per strand?
improved plow steel mean?
When using Crosby clips, which of the To determine the correct minimum spacing multiply the rope diameter times 6.
following statements is correct?
When handling and storing a freight With the platform on edge, handle it from the ends and move on rollers.
platform, what do you need to keep in
mind?
Both b, and c.
Which of the following statements is true
b. Fasten the hoist to a beam or other building structure.
concerning capstans?
c. To interrupt hoisting ease off on the pulling rope
When choosing planks for hoisting, what Use only scaffold grade lumber
must be considered?
The distance between the counterweight Runby
buffer strike plate and the striking surface
of the counterweight buffer when the car
floor is level with the top terminal landing
is known as
What type of wrench is used to align the Spud Wrench
holes for rail installation?
Which of the following wrenches is used Strap Wrench
to thread pipes with polished surfaces
together?
Which of the following statements applies Hacksaw blades must be installed with the teeth facing forward.
to the use of a hacksaw on the job?
The operation of the down final limit both directions of travel
switch will prevent movement of the car
by normal operating devices in ...
Which of the following statements is Metal ladders should never be used
correct regarding ladders?
What safety precaution is most important Pipe rollers must be picked up by the hollow inner pan
when using rollers to move heavy
equipment?
What are two things a compound mitre Bevel and mitre cuts can be made at the same time.
saw does best at the same time?
When the pit down final limit switch is Will not run at all
actuated, the car...
Why do we use laminated glass in the If the glass cracks the plastic interlayer holds the fragments.
walls of glass elevator cabs?
Save
Students also studied
NEIEP 200 Final EXAM COMPREHE... NEIEP 200 Final Review Relias Dysrhythmia Interpretation NE
Teacher 108 terms 73 terms 36 terms 58
Georges20_ Preview annablake128 Preview sunnydaisy48 Preview
Practice questions for this set
Learn 1 /7 Study with Learn
How are the ends of rails made so they may be joined together?
Choose an answer
1 The ends are riveted together 2 The ends are welded together
3 The ends are bolted together 4 The ends have a tongue and groove
Don't know?
Terms in this set (73)
Which lay of wire rope has the strand Regular Lay
wires in line with the rope axis?
At what speed should the counterweight Up to 10% higher than the car governor
safeties be set to trip?
Which type of safety uses an oil buffer Type C
between the car and safety planks?
What is the purpose of the terminal slow down and stop the car automatically at or near the top or bottom landing
motion switch?
If you have a 3500 lb. car rated at 4000 5100 lbs.
lbs. capacity, how much should the
counterweight assembly weigh for a
normal 40% installation?
, When the pit directional limit switch is Up
actuated, the normal circuits will allow the
car to run
_______should not be disassembled in the Oil Buffers
field.
The loss of traction between the hoist The elevator car being pulled into the over head.
ropes and the machine driver when the
counterweight lands on its buffer avoids...
Refer to Table 1. With a safety factor of 5, 52,000 lbs.
what is the breaking strength for 1 1/8"
nylon rope?
Which of the following applies to rope Prevent manila rope from unraveling by using whipping.
usage?
What does the designation 3/8" 6 X 30 It is a high strength cable with 6 strands composed of 30 wires per strand?
improved plow steel mean?
When using Crosby clips, which of the To determine the correct minimum spacing multiply the rope diameter times 6.
following statements is correct?
When handling and storing a freight With the platform on edge, handle it from the ends and move on rollers.
platform, what do you need to keep in
mind?
Both b, and c.
Which of the following statements is true
b. Fasten the hoist to a beam or other building structure.
concerning capstans?
c. To interrupt hoisting ease off on the pulling rope
When choosing planks for hoisting, what Use only scaffold grade lumber
must be considered?
The distance between the counterweight Runby
buffer strike plate and the striking surface
of the counterweight buffer when the car
floor is level with the top terminal landing
is known as
What type of wrench is used to align the Spud Wrench
holes for rail installation?
Which of the following wrenches is used Strap Wrench
to thread pipes with polished surfaces
together?
Which of the following statements applies Hacksaw blades must be installed with the teeth facing forward.
to the use of a hacksaw on the job?
The operation of the down final limit both directions of travel
switch will prevent movement of the car
by normal operating devices in ...
Which of the following statements is Metal ladders should never be used
correct regarding ladders?
What safety precaution is most important Pipe rollers must be picked up by the hollow inner pan
when using rollers to move heavy
equipment?
What are two things a compound mitre Bevel and mitre cuts can be made at the same time.
saw does best at the same time?
When the pit down final limit switch is Will not run at all
actuated, the car...
Why do we use laminated glass in the If the glass cracks the plastic interlayer holds the fragments.
walls of glass elevator cabs?
