NCCER MILLWRIGHT PRACTICE EXAM
2 ACTUAL QUESTIONS AND CORRECT
DETAILED ANSWERS (VERIFIED
ANSWERS)
If the seal was not properly aligned or there is excessive wear in
some bearing or shaft,_______ wear tracks will be the indicator -
correct answer ✅unusual
For removing hard to remove gasket materials found on sealing
surfaces, ______ is recommended -
correct answer ✅sharpened brass putty knife
Apprenticeship training is_______ -
correct answer ✅Conducted on the job
Charting alignment on a graph requires a chart that is divided into
thousandths of an inch vertically for the indicator readings and into
whole inches horizontally for the__________ -
correct answer ✅distance
The orthographic drawing may contain a dashed or _______ line -
correct answer ✅hidden
,NCCER MILLWRIGHT PRACTICE EXAM
2 ACTUAL QUESTIONS AND CORRECT
DETAILED ANSWERS (VERIFIED
ANSWERS)
In order to shoot through a test object and project an image onto a
detector or a sheet of film, radiography uses a source of
penetrating called _______ -
correct answer ✅Radiation
Which of the following task would you not perform with dividers? -
correct answer ✅*scribe circles
*transfer measurements
*compare distances
<measure angles
The over speed trip device is actuated when the turbine reaches a
predetermined limit usually _________% above normal full-load
speed -
correct answer ✅10%
Positive results in an offset measurement mean that the MTBM is
_____ or on the 3-o'clock side. -
correct answer ✅high
, NCCER MILLWRIGHT PRACTICE EXAM
2 ACTUAL QUESTIONS AND CORRECT
DETAILED ANSWERS (VERIFIED
ANSWERS)
The coupling gap is set, and then the ______ is measured -
correct answer ✅offset misalignment
In a hydraulic system, movement depends on_____ -
correct answer ✅pressure
Fractional dimensions are used on objects such as _______ or
______ -
correct answer ✅furniture or utility items
If the cause of the problem is not immediately understood, the
process of________is often the procedure of choice -
correct answer ✅elimination
When applying sealant to the sealing gland flanges, keep the
sealant away from the inside edges of the flange by at least_______
inch -
correct answer ✅3/16
2 ACTUAL QUESTIONS AND CORRECT
DETAILED ANSWERS (VERIFIED
ANSWERS)
If the seal was not properly aligned or there is excessive wear in
some bearing or shaft,_______ wear tracks will be the indicator -
correct answer ✅unusual
For removing hard to remove gasket materials found on sealing
surfaces, ______ is recommended -
correct answer ✅sharpened brass putty knife
Apprenticeship training is_______ -
correct answer ✅Conducted on the job
Charting alignment on a graph requires a chart that is divided into
thousandths of an inch vertically for the indicator readings and into
whole inches horizontally for the__________ -
correct answer ✅distance
The orthographic drawing may contain a dashed or _______ line -
correct answer ✅hidden
,NCCER MILLWRIGHT PRACTICE EXAM
2 ACTUAL QUESTIONS AND CORRECT
DETAILED ANSWERS (VERIFIED
ANSWERS)
In order to shoot through a test object and project an image onto a
detector or a sheet of film, radiography uses a source of
penetrating called _______ -
correct answer ✅Radiation
Which of the following task would you not perform with dividers? -
correct answer ✅*scribe circles
*transfer measurements
*compare distances
<measure angles
The over speed trip device is actuated when the turbine reaches a
predetermined limit usually _________% above normal full-load
speed -
correct answer ✅10%
Positive results in an offset measurement mean that the MTBM is
_____ or on the 3-o'clock side. -
correct answer ✅high
, NCCER MILLWRIGHT PRACTICE EXAM
2 ACTUAL QUESTIONS AND CORRECT
DETAILED ANSWERS (VERIFIED
ANSWERS)
The coupling gap is set, and then the ______ is measured -
correct answer ✅offset misalignment
In a hydraulic system, movement depends on_____ -
correct answer ✅pressure
Fractional dimensions are used on objects such as _______ or
______ -
correct answer ✅furniture or utility items
If the cause of the problem is not immediately understood, the
process of________is often the procedure of choice -
correct answer ✅elimination
When applying sealant to the sealing gland flanges, keep the
sealant away from the inside edges of the flange by at least_______
inch -
correct answer ✅3/16
