Smog Check Inspector Level 2 Exam
(Latest Update ) | Final
Review Questions & Answers |
Grade A | 100 % Correct
Question:
The visible smoke inspection consists of:
A. Crank case test, BAR snap test, idle test
B. Crankcase, TSI, BAR snap test, idle test
C. Crankcase test, idle test, liquid fuel leaks
D. None of the above
Answer:
B. Crankcase , TSI, BAR snap test, idle test
,Question:
A technician places the vehicle's drive wheel on the dynamometer. What is
the correct clearance of the dynamometer side rollers to the sidewall of the
drive tires?
A. 12 to 14 inches for front wheel drive vehicles
B. The sides rollers are not necessary during an ASM test
C. 3 to 5 inches for all vehicles, unless specified otherwise
D. The rollers must contact the sidewall of the tires for safety
Answer:
C. 3 to 5 inches for all vehicles, unless specified otherwise
Question:
A technician is conducting an EGR functional test. When applying vacuum to
the EGR valve the engine stalls and dies. How should the technician enter this
information into the EIS?
A. Pass. The valve is responding to vacuum
B. Fail. The vehicle is not supposed to stall while applying vacuum to the EGR
C. The technician cannot make an entry at this point as he or she has not
finished conducting the test
D. None of the above
Answer:
A. Pass. The valve is responding to vacuum
, Question:
A technician is conducting the Ignition Timing functional test on a 1990MY
vehicle. What are common sources for obtaining the timing information for
this vehicle?
A. Under-hood label
B. ALLDATA and/or Mitchell On Demand
C. ECS Manual
D. All of the above
Answer:
D. All of the above
Question:
What MY vehicles are required to receive a Low-Pressure Fuel Evaporative
Test(LPFET) during a Smog Check inspection?
A. 1999 and older gasoline vehicles
B. 2000 and newer gasoline vehicles
C. 1998 and newer diesel vehicles
D. 1995 and older gasoline vehicles
Answer:
D. 1995 and older gasoline vehicles
(Latest Update ) | Final
Review Questions & Answers |
Grade A | 100 % Correct
Question:
The visible smoke inspection consists of:
A. Crank case test, BAR snap test, idle test
B. Crankcase, TSI, BAR snap test, idle test
C. Crankcase test, idle test, liquid fuel leaks
D. None of the above
Answer:
B. Crankcase , TSI, BAR snap test, idle test
,Question:
A technician places the vehicle's drive wheel on the dynamometer. What is
the correct clearance of the dynamometer side rollers to the sidewall of the
drive tires?
A. 12 to 14 inches for front wheel drive vehicles
B. The sides rollers are not necessary during an ASM test
C. 3 to 5 inches for all vehicles, unless specified otherwise
D. The rollers must contact the sidewall of the tires for safety
Answer:
C. 3 to 5 inches for all vehicles, unless specified otherwise
Question:
A technician is conducting an EGR functional test. When applying vacuum to
the EGR valve the engine stalls and dies. How should the technician enter this
information into the EIS?
A. Pass. The valve is responding to vacuum
B. Fail. The vehicle is not supposed to stall while applying vacuum to the EGR
C. The technician cannot make an entry at this point as he or she has not
finished conducting the test
D. None of the above
Answer:
A. Pass. The valve is responding to vacuum
, Question:
A technician is conducting the Ignition Timing functional test on a 1990MY
vehicle. What are common sources for obtaining the timing information for
this vehicle?
A. Under-hood label
B. ALLDATA and/or Mitchell On Demand
C. ECS Manual
D. All of the above
Answer:
D. All of the above
Question:
What MY vehicles are required to receive a Low-Pressure Fuel Evaporative
Test(LPFET) during a Smog Check inspection?
A. 1999 and older gasoline vehicles
B. 2000 and newer gasoline vehicles
C. 1998 and newer diesel vehicles
D. 1995 and older gasoline vehicles
Answer:
D. 1995 and older gasoline vehicles
