Alberta Welding First Year Final AIT Exam 2025/2026 | 100% Verified Questions & Accurate
Answers
A Material Safety Data Sheet must be reviewed whenever new information becomes available or at least
how often? - (ANSWER)every three years
What is the total number of hours of work experience, including technical training, required per year in
the Welder Apprenticeship Program? - (ANSWER)1800
Voltage-sensing wire feeders set their speed according to: - (ANSWER)arc voltage.
How much electrode stickout is recommended when using gas shielded FCAW with 1.2 mm (0.045")
wire? - (ANSWER)10 mm to 19 mm (3/8" to 3/4")
One of the main functions of the contact tube is to: - (ANSWER)transfer current to the electrode.
Flame propagation means the speed at which the fuel gas will travel - (ANSWER)False
What height limitation is in place when using freestanding scaffolding? - (ANSWER)For free standing
scaffolds, the scaffold must not be taller than three (3) times its smallest dimension in height
The best reference point for dimensioning on pressure vessels is the: - (ANSWER)datum line
Which of the following is an abbreviation of a Non destructive test ? - (ANSWER)UT
In common fabricating practice, there are how many basic joint types? - (ANSWER)5
Single "V" butt joints are used on material thicknesses of: - (ANSWER)3/8" -1" (9.5 -25.4mm)
A small change in sling angle can drastically affect the: - (ANSWER)sling load.
, Alberta Welding First Year Final AIT Exam 2025/2026 | 100% Verified Questions & Accurate
Answers
The power sources used for pulsed spray transfer are: - (ANSWER)DC synergic, microprocessor-
controlled.
Single "V" butt joints are used on material thicknesses of: - (ANSWER)3/8" -1" (9.5 -25.4mm)
If you must apply force to a suspended load, always pull the load towards you. - (ANSWER)
When installing clips, the saddle side of the clip must be placed on the: - (ANSWER)Live side of the wire
When balancing a No. 2 welding tip and the acetylene torch needle valve is fully open, the acetylene
regulator should be adjusted so that the flame blows away from the tip _______ inch. (Oxygen needle
valve is closed) - (ANSWER)1/4
Which ferrous-based metals cannot be cut satisfactorily with an oxy-fuel cutting torch? -
(ANSWER)stainless
What is the total number of hours in the first period Welder Training Profile? - (ANSWER)240
When starting a cut on plate, the preheat cones should be held: - (ANSWER)about 3 mm (1/8") above
the surface.
What is the main purpose of the contact tube? - (ANSWER)transfers the welding current to the filler
wire
A steamed vessel is safest to weld on when it is cooled down to room temperature . - (ANSWER)False
Three basic oxy/acetylene flame types are known as: - (ANSWER)carbonizing, neutral, oxidizing
Which of the following is a abbreviation of a welding process? - (ANSWER)OAW
Answers
A Material Safety Data Sheet must be reviewed whenever new information becomes available or at least
how often? - (ANSWER)every three years
What is the total number of hours of work experience, including technical training, required per year in
the Welder Apprenticeship Program? - (ANSWER)1800
Voltage-sensing wire feeders set their speed according to: - (ANSWER)arc voltage.
How much electrode stickout is recommended when using gas shielded FCAW with 1.2 mm (0.045")
wire? - (ANSWER)10 mm to 19 mm (3/8" to 3/4")
One of the main functions of the contact tube is to: - (ANSWER)transfer current to the electrode.
Flame propagation means the speed at which the fuel gas will travel - (ANSWER)False
What height limitation is in place when using freestanding scaffolding? - (ANSWER)For free standing
scaffolds, the scaffold must not be taller than three (3) times its smallest dimension in height
The best reference point for dimensioning on pressure vessels is the: - (ANSWER)datum line
Which of the following is an abbreviation of a Non destructive test ? - (ANSWER)UT
In common fabricating practice, there are how many basic joint types? - (ANSWER)5
Single "V" butt joints are used on material thicknesses of: - (ANSWER)3/8" -1" (9.5 -25.4mm)
A small change in sling angle can drastically affect the: - (ANSWER)sling load.
, Alberta Welding First Year Final AIT Exam 2025/2026 | 100% Verified Questions & Accurate
Answers
The power sources used for pulsed spray transfer are: - (ANSWER)DC synergic, microprocessor-
controlled.
Single "V" butt joints are used on material thicknesses of: - (ANSWER)3/8" -1" (9.5 -25.4mm)
If you must apply force to a suspended load, always pull the load towards you. - (ANSWER)
When installing clips, the saddle side of the clip must be placed on the: - (ANSWER)Live side of the wire
When balancing a No. 2 welding tip and the acetylene torch needle valve is fully open, the acetylene
regulator should be adjusted so that the flame blows away from the tip _______ inch. (Oxygen needle
valve is closed) - (ANSWER)1/4
Which ferrous-based metals cannot be cut satisfactorily with an oxy-fuel cutting torch? -
(ANSWER)stainless
What is the total number of hours in the first period Welder Training Profile? - (ANSWER)240
When starting a cut on plate, the preheat cones should be held: - (ANSWER)about 3 mm (1/8") above
the surface.
What is the main purpose of the contact tube? - (ANSWER)transfers the welding current to the filler
wire
A steamed vessel is safest to weld on when it is cooled down to room temperature . - (ANSWER)False
Three basic oxy/acetylene flame types are known as: - (ANSWER)carbonizing, neutral, oxidizing
Which of the following is a abbreviation of a welding process? - (ANSWER)OAW
