J-STD-001 Exam Questions And Correct Answers
2025/2026 Latest Update (A Pass)
Who is responsible for identifying the assembly class? - CORRECT ANSWER
✔✔- User
What is a defect? - CORRECT ANSWER ✔✔- A condition that may affect the
form, fit, or function of the item in the end use environment
Hardware found to not conform to the requirements of the standard shall be
classified as defects and dispositioned for: - CORRECT ANSWER ✔✔-
[D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: -
CORRECT ANSWER ✔✔- [D1D2D3]
A documented process control system shall be implemented for: - CORRECT
ANSWER ✔✔- [N1N2D3]
The contract shall take precedence over this standard for: - CORRECT ANSWER
✔✔- [D1D2D3]
What is wire overlap? - CORRECT ANSWER ✔✔- When a wire is wrapped more
than 360 and crosses over itself
What is wire over wrap? - CORRECT ANSWER ✔✔- When a wire is wrapped
more than 360 and remains in contact with the terminal
prepma ster
, Manufacturers shall perform 100% inspection unless sampling inspection is
defined for: - CORRECT ANSWER ✔✔- [N1D2D3]
Inspection of soldering and cleanliness shall be performed prior to conformal
coasting, staking, or encapsulation for: - CORRECT ANSWER ✔✔- [N1D2D3]
Illumination at the surface of work stations should be at least what? - CORRECT
ANSWER ✔✔- 1000 lux
What is the tolerance for magnification aids? - CORRECT ANSWER ✔✔- +- 15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: -
CORRECT ANSWER ✔✔- [D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: -
CORRECT ANSWER ✔✔- [N1D2D3]
Manufacturer shall establish an ESD control program for: - CORRECT ANSWER
✔✔- [D1D2D3]
What is J-STD-002? - CORRECT ANSWER ✔✔- Solder-ability tests for
Component leads, terminations, lugs, wires, and terminals
What is J-STD-003? - CORRECT ANSWER ✔✔- Solder ability tests for printed
boards
prepma ster
2025/2026 Latest Update (A Pass)
Who is responsible for identifying the assembly class? - CORRECT ANSWER
✔✔- User
What is a defect? - CORRECT ANSWER ✔✔- A condition that may affect the
form, fit, or function of the item in the end use environment
Hardware found to not conform to the requirements of the standard shall be
classified as defects and dispositioned for: - CORRECT ANSWER ✔✔-
[D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: -
CORRECT ANSWER ✔✔- [D1D2D3]
A documented process control system shall be implemented for: - CORRECT
ANSWER ✔✔- [N1N2D3]
The contract shall take precedence over this standard for: - CORRECT ANSWER
✔✔- [D1D2D3]
What is wire overlap? - CORRECT ANSWER ✔✔- When a wire is wrapped more
than 360 and crosses over itself
What is wire over wrap? - CORRECT ANSWER ✔✔- When a wire is wrapped
more than 360 and remains in contact with the terminal
prepma ster
, Manufacturers shall perform 100% inspection unless sampling inspection is
defined for: - CORRECT ANSWER ✔✔- [N1D2D3]
Inspection of soldering and cleanliness shall be performed prior to conformal
coasting, staking, or encapsulation for: - CORRECT ANSWER ✔✔- [N1D2D3]
Illumination at the surface of work stations should be at least what? - CORRECT
ANSWER ✔✔- 1000 lux
What is the tolerance for magnification aids? - CORRECT ANSWER ✔✔- +- 15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: -
CORRECT ANSWER ✔✔- [D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: -
CORRECT ANSWER ✔✔- [N1D2D3]
Manufacturer shall establish an ESD control program for: - CORRECT ANSWER
✔✔- [D1D2D3]
What is J-STD-002? - CORRECT ANSWER ✔✔- Solder-ability tests for
Component leads, terminations, lugs, wires, and terminals
What is J-STD-003? - CORRECT ANSWER ✔✔- Solder ability tests for printed
boards
prepma ster
