CSX RCO Study Guide Questions
with Accurate Answers
1 correct answer The couple speed is regulated to ____ mph.
1, 2 correct answer There is a communication range of ___ mile in direct mode
and ___ miles in repeater mode.
130, 145 correct answer The main reservoir gauge is fully charged and fluctuates
between _____ and ____ psi.
15 correct answer In the coast b setting on the speed selector lever, ____ lbs of
independent brake pressure are applied.
45, 15 correct answer The tilt switch senses when the OCU is tilted more than
_____ degrees +/- _____ degrees.
46, 15, restricted correct answer All RCL or RCP movements must be made in
accordance with rule ____ not exceeding _____ mph. Movements on main or
signaled track will be made at _____ speed regardless of signal indication.
6, 3 correct answer You must hold the OCU ____ " to ____ ft from the IR/RF Link
port when setting up the remote control link.
A correct answer On CSXT, the ____ position will be used when one OCU is linked
to the RCL.
, accessory circuit breakers correct answer The _______ _____ ______ serve
specific functions that may not be necessary for locomotive operation.
air brake gauges correct answer ______ _____ ______ on the control stand is
used to measure air pressures for air brake operation.
Alarm & Indicator lights correct answer The _______ _______ _____ on the
engine control panel indicate a fault or condition of the locomotive.
AMP gauge correct answer The _____ _____ on the control stand indicates
locomotive electrical output
Automatic (train) brake correct answer _____ ______ on the control stand is used
to apply air brakes on the locomotive and train.
brake pipe gauge (white needle) correct answer the _____ _____ ____ indicates
brake pipe pressure at the locomotive.
Cab, Air, Remote, Test correct answer The acronym "CART" strand for _____,
_____, _____, and ______, and identifies the order in which we set up the
locomotive for remote control operations.
control speed, slow, stop correct answer The speed selector is the preferred
method to ______ ______, _____, and _____ the movement.
control stand correct answer The ______ ______ consists of air brake and
electrical devices to control locomotive operation.
with Accurate Answers
1 correct answer The couple speed is regulated to ____ mph.
1, 2 correct answer There is a communication range of ___ mile in direct mode
and ___ miles in repeater mode.
130, 145 correct answer The main reservoir gauge is fully charged and fluctuates
between _____ and ____ psi.
15 correct answer In the coast b setting on the speed selector lever, ____ lbs of
independent brake pressure are applied.
45, 15 correct answer The tilt switch senses when the OCU is tilted more than
_____ degrees +/- _____ degrees.
46, 15, restricted correct answer All RCL or RCP movements must be made in
accordance with rule ____ not exceeding _____ mph. Movements on main or
signaled track will be made at _____ speed regardless of signal indication.
6, 3 correct answer You must hold the OCU ____ " to ____ ft from the IR/RF Link
port when setting up the remote control link.
A correct answer On CSXT, the ____ position will be used when one OCU is linked
to the RCL.
, accessory circuit breakers correct answer The _______ _____ ______ serve
specific functions that may not be necessary for locomotive operation.
air brake gauges correct answer ______ _____ ______ on the control stand is
used to measure air pressures for air brake operation.
Alarm & Indicator lights correct answer The _______ _______ _____ on the
engine control panel indicate a fault or condition of the locomotive.
AMP gauge correct answer The _____ _____ on the control stand indicates
locomotive electrical output
Automatic (train) brake correct answer _____ ______ on the control stand is used
to apply air brakes on the locomotive and train.
brake pipe gauge (white needle) correct answer the _____ _____ ____ indicates
brake pipe pressure at the locomotive.
Cab, Air, Remote, Test correct answer The acronym "CART" strand for _____,
_____, _____, and ______, and identifies the order in which we set up the
locomotive for remote control operations.
control speed, slow, stop correct answer The speed selector is the preferred
method to ______ ______, _____, and _____ the movement.
control stand correct answer The ______ ______ consists of air brake and
electrical devices to control locomotive operation.
