FIRE II FINAL Exam 2025–2026 Accurate Real
Exam Questions and Verified Correct Answers
JUST RELEASED
Which of the following is a common handsaw?
A. Hacksaw
B. Chain Saw
C. Circular Saw
D. Reciprocating Saw - answer>>>A
p.584
Which of the following comes in small battery-powered units?
A. Hacksaw
B. Chain Saw
C. Rotary Saw
D. Circular Saw - answer>>>D
p.586
The blades of a rotary saw may spin at more than:
A. 4,000 rpm
B. 6,000 rpm
C. 8,000 rpm
D. 10,000 rpm - answer>>>B
p.586
Which of the following should be equipped with kickback protection and brakes for
safety?
,A. Chain Saw
B. Rotary Saw
C. Circular Saw
D. Reciprocating Saw - answer>>>A
p.586
Which of the following is most often constructed from a single-piece of high-carbon steel,
approximately 30 to 36 inches (762mm to 900mm)?
A. Pushing Tools
B. Striking Tools
C. Sharpening Tools
D. Manual Prying Tools - answer>>>D
p.588
A hydraulic spreader tip can be spread as much as:
A. 28 inches (711 mm).
B. 32 inches (800 mm).
C. 36 inches (914 mm).
D. 48 inches (1219 mm). - answer>>>B
p.588
Which of the following is an example of a push/pull tool?
A. Hux bar
B.Pike pole
C.Drywall saw
D.Battering ram - answer>>>B
p.589
,Where are the hinges of an outward swinging door mounted?
A.Inside
B.Outside
C.One side
D.Both sides - answer>>>B
p.600
A double swinging door secured by a mortise lock can be pried to:
A.break open.
B.let the bolt slip past receiver.
C.turn knob to retract latch bolt.
D.operate with doorknob or lever. - answer>>>B
p.600
Which of the following is used to lock single or double-swinging doors?
A.Drop bar
B.Chain lock
C.Door limiter
D.Surface bolt - answer>>>A
p.600
Which of the following can be used to create an opening for a penetrating nozzle?
A.Pry bar
B.Stitch drill
C.Chain saw
D.Rotary saw - answer>>>B
, p.621
A chain-link fence should be cut quickly with a (an):
A.axe.
B.bolt cutter.
C.rotary saw.
D.cutting torch. - answer>>>C
p.621
NFPA¨ 1931 requires which of the following markings on fire service ladders?
A.Apparatus designation
B.Local inventory number
C.Manufacturer's name plate
D.White or reflective top rung - answer>>>C
pg.659
Fire service ladders meeting the requirements of NFPA¨ 1931 are required to have:
A.a certification label indicating the ladder meets NFPA¨ 1931.
B.a locally assigned apparatus designation and inventory number.
C.a mark indicating the balance point of ladders less than 24 feet (7 m).
D.a label indicating the position of the ladder when properly racked on the apparatus. -
answer>>>A
p.659
Which of the following statements about heat sensor labels is MOST accurate?
A.Heat sensors are required on all wood ladders.
B.Heat sensors are preset to change color at 300¡ F (149¡ C).
Exam Questions and Verified Correct Answers
JUST RELEASED
Which of the following is a common handsaw?
A. Hacksaw
B. Chain Saw
C. Circular Saw
D. Reciprocating Saw - answer>>>A
p.584
Which of the following comes in small battery-powered units?
A. Hacksaw
B. Chain Saw
C. Rotary Saw
D. Circular Saw - answer>>>D
p.586
The blades of a rotary saw may spin at more than:
A. 4,000 rpm
B. 6,000 rpm
C. 8,000 rpm
D. 10,000 rpm - answer>>>B
p.586
Which of the following should be equipped with kickback protection and brakes for
safety?
,A. Chain Saw
B. Rotary Saw
C. Circular Saw
D. Reciprocating Saw - answer>>>A
p.586
Which of the following is most often constructed from a single-piece of high-carbon steel,
approximately 30 to 36 inches (762mm to 900mm)?
A. Pushing Tools
B. Striking Tools
C. Sharpening Tools
D. Manual Prying Tools - answer>>>D
p.588
A hydraulic spreader tip can be spread as much as:
A. 28 inches (711 mm).
B. 32 inches (800 mm).
C. 36 inches (914 mm).
D. 48 inches (1219 mm). - answer>>>B
p.588
Which of the following is an example of a push/pull tool?
A. Hux bar
B.Pike pole
C.Drywall saw
D.Battering ram - answer>>>B
p.589
,Where are the hinges of an outward swinging door mounted?
A.Inside
B.Outside
C.One side
D.Both sides - answer>>>B
p.600
A double swinging door secured by a mortise lock can be pried to:
A.break open.
B.let the bolt slip past receiver.
C.turn knob to retract latch bolt.
D.operate with doorknob or lever. - answer>>>B
p.600
Which of the following is used to lock single or double-swinging doors?
A.Drop bar
B.Chain lock
C.Door limiter
D.Surface bolt - answer>>>A
p.600
Which of the following can be used to create an opening for a penetrating nozzle?
A.Pry bar
B.Stitch drill
C.Chain saw
D.Rotary saw - answer>>>B
, p.621
A chain-link fence should be cut quickly with a (an):
A.axe.
B.bolt cutter.
C.rotary saw.
D.cutting torch. - answer>>>C
p.621
NFPA¨ 1931 requires which of the following markings on fire service ladders?
A.Apparatus designation
B.Local inventory number
C.Manufacturer's name plate
D.White or reflective top rung - answer>>>C
pg.659
Fire service ladders meeting the requirements of NFPA¨ 1931 are required to have:
A.a certification label indicating the ladder meets NFPA¨ 1931.
B.a locally assigned apparatus designation and inventory number.
C.a mark indicating the balance point of ladders less than 24 feet (7 m).
D.a label indicating the position of the ladder when properly racked on the apparatus. -
answer>>>A
p.659
Which of the following statements about heat sensor labels is MOST accurate?
A.Heat sensors are required on all wood ladders.
B.Heat sensors are preset to change color at 300¡ F (149¡ C).
