Flagger ATSSA Exam Questions
with 100% Correct Solutions||100%
Guaranteed Pass!!!ALREADY
GRADED!!
1. While hammer testing a pole, this range circumferentially should
be tested - ANSWER ✓ Ground to as high as can be reached
2. Under OSHA standards, bonds between the suspension strand and
the existing ground shall be at least this - ANSWER ✓ No. 6 AWG
copper
3. PCB - ANSWER ✓ polychlorinated biphenyls
4. Cancer-causing agent older transformers may contain - ANSWER
✓ PCB (polychlorinated biphenyls)
5. The (2) times durring ladder handling when accidents are most
likely to occur - ANSWER ✓ -On the way down -Within 10 feet of
the ground
6. Instance when fall protection is necessary - ANSWER ✓ Anytime
working near an edge that is 6 feet or more above a lower surface
7. (4) situations when OSHA requires the use of a 5-point safety
harness - ANSWER ✓ -Bucket trucks -Climbing towers -Rooftops
-Confined Space
8. Definiton of low slope roof - ANSWER ✓ A roof having a slope
less than or equal to 4:12
, 9. Definition of steep roof - ANSWER ✓ A roof having a slope
greater than 4:12
10. (3) Types of fall protection for unprotected side or edge -
ANSWER ✓ -Guardrail system (toe boards for steep roof) -Safety
net system -Personal fall arrest system
11. Required fall protection for low slope roof less than 50 ft
width - ANSWER ✓ Safety monitoring system
12. (4) Required fall protection devices for low slope roof greater
than 50 ft width - ANSWER ✓ -Guardrail -Safety net -Personal
fall arrest system -Warning line
13. Minimum height of guardrail - ANSWER ✓ Between 39''
and 45''
14. Minimum height of safety nets below the working
enviornment - ANSWER ✓ 30 ft
15. Distance of safety line from roof edge - ANSWER ✓ 6 ft
16. Person who accompanies workers on roof to warn workers
who get to close to the edge - ANSWER ✓ Safety Monitoring
System
17. (4) Components of personal fall arrest system - ANSWER ✓
-Rigged for 6ft free fall max, no contact with lower surface -
Anchor point must support up to 5000 lbs per employee -D-ring
attatchment will be at back, shoulder level -Must be inspected prior
to each use
with 100% Correct Solutions||100%
Guaranteed Pass!!!ALREADY
GRADED!!
1. While hammer testing a pole, this range circumferentially should
be tested - ANSWER ✓ Ground to as high as can be reached
2. Under OSHA standards, bonds between the suspension strand and
the existing ground shall be at least this - ANSWER ✓ No. 6 AWG
copper
3. PCB - ANSWER ✓ polychlorinated biphenyls
4. Cancer-causing agent older transformers may contain - ANSWER
✓ PCB (polychlorinated biphenyls)
5. The (2) times durring ladder handling when accidents are most
likely to occur - ANSWER ✓ -On the way down -Within 10 feet of
the ground
6. Instance when fall protection is necessary - ANSWER ✓ Anytime
working near an edge that is 6 feet or more above a lower surface
7. (4) situations when OSHA requires the use of a 5-point safety
harness - ANSWER ✓ -Bucket trucks -Climbing towers -Rooftops
-Confined Space
8. Definiton of low slope roof - ANSWER ✓ A roof having a slope
less than or equal to 4:12
, 9. Definition of steep roof - ANSWER ✓ A roof having a slope
greater than 4:12
10. (3) Types of fall protection for unprotected side or edge -
ANSWER ✓ -Guardrail system (toe boards for steep roof) -Safety
net system -Personal fall arrest system
11. Required fall protection for low slope roof less than 50 ft
width - ANSWER ✓ Safety monitoring system
12. (4) Required fall protection devices for low slope roof greater
than 50 ft width - ANSWER ✓ -Guardrail -Safety net -Personal
fall arrest system -Warning line
13. Minimum height of guardrail - ANSWER ✓ Between 39''
and 45''
14. Minimum height of safety nets below the working
enviornment - ANSWER ✓ 30 ft
15. Distance of safety line from roof edge - ANSWER ✓ 6 ft
16. Person who accompanies workers on roof to warn workers
who get to close to the edge - ANSWER ✓ Safety Monitoring
System
17. (4) Components of personal fall arrest system - ANSWER ✓
-Rigged for 6ft free fall max, no contact with lower surface -
Anchor point must support up to 5000 lbs per employee -D-ring
attatchment will be at back, shoulder level -Must be inspected prior
to each use
