POWER TOOLS Exam 2025 Questions
and Answers
REVERSING SWITCH - --Answer --a device on a power drill that enable
a user to back out a drill bit that is stuck in the work material is called a
NUMBER OF DRILL BLOWS PER MINUTE - --Answer --a hammer drill
has a adjustable ring that can be turned to adjust the
PNEUMATIC IMPACT WRENCH - --Answer --a pneumatic power tool
that is best suited for fastening, tightening, and loosening nuts and bolts is a
IT IS THE PROPER WAY TO START CUTTING MATERIAL WITH A
CIRCULAR SAW - --Answer --rev the saw to full speed and slowly move it
forward into the material.
ELECTRIC TOOLS - --Answer --are powered by electricity. They are
operated from either an alternating current (AC) source (such as a wall receptacle)
or a direct current (DC) source (such as a battery).
ALTERNATING CURRENT (AC) - --Answer --source such as a wall
receptacle.
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 1
,DIRECT CURRENT (DC) - --Answer --source such as a battery.
PNEUMATIC TOOLS - --Answer --are powered by air. Electric or
gasoline-powered compressors produce the air pressure. Air hammers and
pneumatic nailers are examples of pneumatic tools.
HYDRAULIC TOOLS - --Answer --are powered by fluid pressure. Hand
pumps or electric pumps are used to produce the fluid pressure. Pipebenders,
jackhammers, and Porta-powers are examples of:
FRAYED - --Answer --of a fabric, rope, or cord, unravel or become worn at
the edge, typically through constant rubbing.
TRIGGER LOCK - --Answer --a small lever, switch, or part that can be
used to activate a locking catch or spring to hold a power tool trigger in the
operating mode without finger pressure.
POWER DRILL - --Answer --is most commonly used to make holes by
spinning drill bits into wood, metal, plastic, and other materials.
POWER DRILL - --Answer --also used as a sander, polisher, screwdriver,
grinder, or countersink.
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 2
, ELECTRIC, CORDLESS, ELECTROMAGNETIC, HAMMER, PNEUMATIC,
ELECTRIC SCREWDRIVER - --Answer --common types of power drills
include:
TWIST DRILL BIT - --Answer --is used to drill wood and plastics at high
speeds or to drill metal at a lower speed.
FORSTNER BIT - --Answer --is used on wood and is particulary good for
boring a flat-bottom hole.
PADDLE OR SPADE BIT - --Answer --is also used in wood.
THE BIT SIZE - --Answer --is measured by the paddle's diameter which
generally ranges from 1/2, to 1 1/2 inches.
MASONRY BIT - --Answer --has a carbide tip, is used in concrete, stone,
slate, and ceramic material.
AUGER BIT - --Answer --is used for drilling wood and other soft materials,
but not for drilling metal. It is designed for use at a very low speed.
CHUCK - --Answer --all bits are held in a drill by the l ______
CHUCK KEY - --Answer --keyed chuck are opened and closed using a
________, they are typically interchangeable in design, but there are different sizes,
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 3
and Answers
REVERSING SWITCH - --Answer --a device on a power drill that enable
a user to back out a drill bit that is stuck in the work material is called a
NUMBER OF DRILL BLOWS PER MINUTE - --Answer --a hammer drill
has a adjustable ring that can be turned to adjust the
PNEUMATIC IMPACT WRENCH - --Answer --a pneumatic power tool
that is best suited for fastening, tightening, and loosening nuts and bolts is a
IT IS THE PROPER WAY TO START CUTTING MATERIAL WITH A
CIRCULAR SAW - --Answer --rev the saw to full speed and slowly move it
forward into the material.
ELECTRIC TOOLS - --Answer --are powered by electricity. They are
operated from either an alternating current (AC) source (such as a wall receptacle)
or a direct current (DC) source (such as a battery).
ALTERNATING CURRENT (AC) - --Answer --source such as a wall
receptacle.
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 1
,DIRECT CURRENT (DC) - --Answer --source such as a battery.
PNEUMATIC TOOLS - --Answer --are powered by air. Electric or
gasoline-powered compressors produce the air pressure. Air hammers and
pneumatic nailers are examples of pneumatic tools.
HYDRAULIC TOOLS - --Answer --are powered by fluid pressure. Hand
pumps or electric pumps are used to produce the fluid pressure. Pipebenders,
jackhammers, and Porta-powers are examples of:
FRAYED - --Answer --of a fabric, rope, or cord, unravel or become worn at
the edge, typically through constant rubbing.
TRIGGER LOCK - --Answer --a small lever, switch, or part that can be
used to activate a locking catch or spring to hold a power tool trigger in the
operating mode without finger pressure.
POWER DRILL - --Answer --is most commonly used to make holes by
spinning drill bits into wood, metal, plastic, and other materials.
POWER DRILL - --Answer --also used as a sander, polisher, screwdriver,
grinder, or countersink.
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 2
, ELECTRIC, CORDLESS, ELECTROMAGNETIC, HAMMER, PNEUMATIC,
ELECTRIC SCREWDRIVER - --Answer --common types of power drills
include:
TWIST DRILL BIT - --Answer --is used to drill wood and plastics at high
speeds or to drill metal at a lower speed.
FORSTNER BIT - --Answer --is used on wood and is particulary good for
boring a flat-bottom hole.
PADDLE OR SPADE BIT - --Answer --is also used in wood.
THE BIT SIZE - --Answer --is measured by the paddle's diameter which
generally ranges from 1/2, to 1 1/2 inches.
MASONRY BIT - --Answer --has a carbide tip, is used in concrete, stone,
slate, and ceramic material.
AUGER BIT - --Answer --is used for drilling wood and other soft materials,
but not for drilling metal. It is designed for use at a very low speed.
CHUCK - --Answer --all bits are held in a drill by the l ______
CHUCK KEY - --Answer --keyed chuck are opened and closed using a
________, they are typically interchangeable in design, but there are different sizes,
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 3
