MSSC MAINTENANCE EXAM
STUDY GUIDE QUESTIONS WITH
CORRECT ANSWERS
Every machine contains potential hazards. When using a lathe, you should be especially
| | | | | | | | | | | |
mindful of: - ANSWER D: Wrap points.
| | | | | | |
ANSWER A. OSHA regulates and enforces most workplace dangers and safety
| | | | | | | | | |
systems.
|
A technical manual typically contains the following information, with the exception: -
| | | | | | | | | | |
ANSWER C: The cost of the equipment
| | | | | | |
To achieve the best fit between mating gears, you should: - ANSWER B. Make them fit
| | | | | | | | | | | | | | |
with a fine-lapping compound.
| | | |
Which of the following describes a flammable material? - ANSWER C: gasoline.
| | | | | | | | | | |
Keeping correct records is an essential component of a preventive maintenance
| | | | | | | | | |
program. A maintenance log includes: - ANSWER Results of testing, inspections, and
| | | | | | | | | | | |
maintenance schedule
| |
During an alignment check between two timing pulleys, have
| | toensure | | | | | | | |
appropriate belt operation: - ANSWER A: At least three points of contact.
| | | | | | | | | | | |
The appropriate oil level in a submerged oil ball bearing system is immersing. -
| | | | | | | | | | | | |
ANSWER C. Half the bottom ball of the bearing.
| | | | | | | | |
Before using any item or piece of equipment, you must be trained in its safe use. Tool
| | | | | | | | | | | | | | | |
and equipment training is provided by: - Answer. A supervisor or experienced
| | | | | | | | | | | |
coworker, the equipment maker, and an on-site or online training course
| | | | | | | | | | |
, A standard operating procedure (SOP) contains a complete set of instructions for
| | | | | | | | | | |
doing a specific task in the form of a written description. The technique is documented
| | | | | | | | | | | | | | |
under the standard operating procedures: - ANSWER On a route sheet, a log book, or
| | | | | | | | | | | | | | |
on a computer
| | |
A power tool safety interlock is designed to prevent a tool from being operated unless
| | | | | | | | | | | | | |
specific circumstances are met.
| | | |
Which safety color is most typically used to represent dangerous equipment or a
| | | | | | | | | | | |
machine component? - Answer: C. Orange
| | | | | |
Proper body mechanics are crucial. When pulling an object, all of the following
| | | | | | | | | | | |
principles must be followed EXCEPT: - ANSWER A. Applying the work to your
| | | | | | | | | | | | |
forearms.
|
Which of the following is true about double-pitch chains: - ANSWER B: The side
| | | | | | | | | | | | |
plates have been stretched to double the normal pitch.
| | | | | | | | |
Tap drill charts are based on what number of threads? - Answer C: 75 percent
| | | | | | | | | | | | | |
Which of the following tools is not a measuring instrument? - ANSWER D:
| | | | | | | | | | | |
Adjustable wrench
| |
What are the most typical causes of bearing failure? - Answer D: Both pollution and
| | | | | | | | | | | | | |
misalignment.
|
A "Grade 5" bolt has
| | | | | cuts on its head. - Answer B: Three.
| | | | | | |
STUDY GUIDE QUESTIONS WITH
CORRECT ANSWERS
Every machine contains potential hazards. When using a lathe, you should be especially
| | | | | | | | | | | |
mindful of: - ANSWER D: Wrap points.
| | | | | | |
ANSWER A. OSHA regulates and enforces most workplace dangers and safety
| | | | | | | | | |
systems.
|
A technical manual typically contains the following information, with the exception: -
| | | | | | | | | | |
ANSWER C: The cost of the equipment
| | | | | | |
To achieve the best fit between mating gears, you should: - ANSWER B. Make them fit
| | | | | | | | | | | | | | |
with a fine-lapping compound.
| | | |
Which of the following describes a flammable material? - ANSWER C: gasoline.
| | | | | | | | | | |
Keeping correct records is an essential component of a preventive maintenance
| | | | | | | | | |
program. A maintenance log includes: - ANSWER Results of testing, inspections, and
| | | | | | | | | | | |
maintenance schedule
| |
During an alignment check between two timing pulleys, have
| | toensure | | | | | | | |
appropriate belt operation: - ANSWER A: At least three points of contact.
| | | | | | | | | | | |
The appropriate oil level in a submerged oil ball bearing system is immersing. -
| | | | | | | | | | | | |
ANSWER C. Half the bottom ball of the bearing.
| | | | | | | | |
Before using any item or piece of equipment, you must be trained in its safe use. Tool
| | | | | | | | | | | | | | | |
and equipment training is provided by: - Answer. A supervisor or experienced
| | | | | | | | | | | |
coworker, the equipment maker, and an on-site or online training course
| | | | | | | | | | |
, A standard operating procedure (SOP) contains a complete set of instructions for
| | | | | | | | | | |
doing a specific task in the form of a written description. The technique is documented
| | | | | | | | | | | | | | |
under the standard operating procedures: - ANSWER On a route sheet, a log book, or
| | | | | | | | | | | | | | |
on a computer
| | |
A power tool safety interlock is designed to prevent a tool from being operated unless
| | | | | | | | | | | | | |
specific circumstances are met.
| | | |
Which safety color is most typically used to represent dangerous equipment or a
| | | | | | | | | | | |
machine component? - Answer: C. Orange
| | | | | |
Proper body mechanics are crucial. When pulling an object, all of the following
| | | | | | | | | | | |
principles must be followed EXCEPT: - ANSWER A. Applying the work to your
| | | | | | | | | | | | |
forearms.
|
Which of the following is true about double-pitch chains: - ANSWER B: The side
| | | | | | | | | | | | |
plates have been stretched to double the normal pitch.
| | | | | | | | |
Tap drill charts are based on what number of threads? - Answer C: 75 percent
| | | | | | | | | | | | | |
Which of the following tools is not a measuring instrument? - ANSWER D:
| | | | | | | | | | | |
Adjustable wrench
| |
What are the most typical causes of bearing failure? - Answer D: Both pollution and
| | | | | | | | | | | | | |
misalignment.
|
A "Grade 5" bolt has
| | | | | cuts on its head. - Answer B: Three.
| | | | | | |
