MSSC Quality Practices and Measurement Exam with Correct Answers 2025

Which type of feature is parallel to the surface being dimensioned? - Correct Ans Dimension line The three standard views of an object are __________. - Correct Ans-Top, front, right side Which type of lines are used to show the counterbored hole in the part? - Correct Ans Hidden lines The number of views in a drawing __________. - Correct Ans-Is the fewest number that shows all of the features and dimensions Which of the following steps is NOT used in the glass box method? - Correct Ans Rotate object in glass box. What type of drawing is shown? - Correct Ans-Multiview The dimensions of raw material supplied by metal suppliers are described by the __________. - Correct Ans-Stock size Which of these requires a computer? - Correct Ans-CAD An isometric drawing is a type of __________. - Correct Ans-Pictorial drawing In the graphic shown, the two circles are __________. - Correct Ans-Concentric Dimensions are used to specify the __________ and location of the features of an object. - Correct Ans-Size What feature in the figure shown is a Chamfer? - Correct Ans-D A __________ dimension is described in inches per foot. - Correct Ans-Shaft taper What is the order of precedence of lines in a drawing? - Correct Ans-Object, Hidden, Center MSSC MSSC MSSC Which of the following is not one of the six rules for dimensioning an object? - Correct Ans-Dimension hidden lines Engineers sometimes use a __________ to measure angles on a drawing. - Correct Ans-Protractor What dimension is indicated in this graphic? - Correct Ans-Height There are 60 minutes of arc in one __________. - Correct Ans-Degree In manufacturing, a blueprint is also called what? - Correct Ans-A technical drawing The distance across the flats of the hex head shown in the part drawing is __________ inches. - Correct Ans-2 ¼ The length of the part shown in the drawing is __________ inches. - Correct Ans-9 ¾ Which type best describes the line indicated in the graphic? - Correct Ans-Object Line Which of the following bolts is a grade 2? - Correct Ans-A The hole shown in the graphic is a __________ hole. - Correct Ans-Counterbore What are the two types of assembly drawings? - Correct Ans-Exploded and basic A sectional view __________. - Correct Ans-All of the above Which of the following is not used to specify a threaded fastener? - Correct Ans-Minor diameter Two types of threads are __________. - Correct Ans-Internal and external In the assembly drawing shown, part 3 screws into part __________. - Correct Ans-4 The material that will be used to create the gear is indicated in the part drawing's title block to be __________. - Correct Ans-Cast iron In a threaded fastener assembly what is designed to protect the threads? - Correct Ans Shank Manufacturing workers can use a calibrated torque wrench to __________. - Correct Ans-Measure the proper amount of torque The part of a drawing that indicates that the drawing has the most up to date information on it is __________. - Correct Ans-Drawing revision level MSSC MSSC What type hole is shown in the figure? - Correct Ans-Counterbored The minor diameter of a screw thread is measured at the __________. - Correct Ans Root of screw thread Section lines in a sectional view are __________. - Correct Ans-All of the above To establish on a drawing that 1/4 inch equals 1 inch, the designer would write __________. - Correct Ans-1/4=1 Metals treated by __________ processes become soft. - Correct Ans-Annealing Where would you look in a title block to see if there has been changes? - Correct Ans Revision number Section lines on a blueprint indicate __________. - Correct Ans-A surface that has been cut A screw with fine thread is represented on a drawing with what designation? - Correct Ans-UNF What is the depth of the countersink in the image? - Correct Ans-0.12 inches What is placed at the arrowheads of the cutting plane line to identify the cutting plane with the proper sectional view? - Correct Ans-Capital letter Assembly drawings rely on reference letters or numbers to __________. - Correct Ans Identify the individual parts If a feature on a drawing is drawn 3 inches long and the scale is 1:4, what is the actual dimension on the object? - Correct Ans-12" The specifications for the length of produced parts is 5.146 inches with a tolerance of ± 0.005. Is a part that has been produced at 5.140 inches out of spec? - Correct Ans-Yes, it is out of spec Which dimension on a production drawing has the most accuracy? - Correct Ans-The one with the most "tolerance" decimal places A datum feature symbol can be connected to __________. - Correct Ans-Any of the above The graphic shown is an example of __________ dimensioning. - Correct Ans-Baseline MSSC MSSC If 4 percent of 1200 production pieces are out of spec, how many are out of spec? - Correct Ans-48 A part measuring 2.54 inches is out of spec if the specification is __________. - Correct Ans-2.00 ± .53 A running fit is also called a(n) __________. - Correct Ans-Sliding fit Form, profile, orientation, location and runout are shown by __________. - Correct Ans GD&T If a drawing shows a part with a diameter of 1.275 ± .003, what is the minimum and maximum size allowed? - Correct Ans-1.272, 1.278 The equipment at a workstation is supposed to produce parts at 2.593, per the part drawing, and has a spec limit of ± 0.004. Is a part that has been produced at 2.590 out of spec? - Correct Ans-No, it is within spec A part measuring 44.85 mm in a process with a tolerance of 45mm ± .28 is considered __________. - Correct Ans-Out of Spec, above the upper tolerance limit Datums are a point of reference to establish __________. - Job tasks - Correct Ans-Datum features The maximum material condition for the part shown is __________. - Correct Ans-15.75 The least material condition for the part shown is __________. - Correct Ans-0.75 Geometric Dimensioning and Toleranci