NCCER Ironworker Final Exam includes accurate and
verified questions covering structural steel installation,
rigging and welding techniques, blueprint reading, safety
procedures, rebar placement, and construction site
protocols. Aligned with NCCER
WHEN AN EXTENSION BOOM IS USED ON A FORKLIFT IT CHANGES ITS: - ans -
CENTER OF GRAVITY
WHERE DOES THE FLUX COME FROM ON A SHEAR STUD? - ans -NIPPLE ON THE
BOTTOM OF THE STUD
WHICH OF THE FOLLOWING WELDING PROCESSES IS NOT TYPICALLY USED IN
STRUCTURAL STEEL APPLICATIONS? - ans -OXY-ACETYLENE WELDING
WHICH OF THE FOLLOWING IS A COMMON TYPE OF ELECTRONIC DISTANCE
MEASUREMENT INSTUMENT? - ans -LASER LIGHT
WHAT STUD WELDING PROCESS IS USED TO INSTALL COMPOSITE CONSTRUCTION
SHEAR STUDS? - ans -GTAW
BEFORE SPREADER BAR OR BEAMS CAN BE USED, THEY MUST HAVE BEEN - ans -
PROPERLY TESTED AND STAMPED
WHEN USING TWO SLINGS TO HOIST A BUNDLE OF LIGHT STEEL MATERIAL, THE
SLINGS SHOULD BE LOOPED IN THE SAME DIRECTION TO PREVENT - ans -
TWISTING OF THE BUNDLE
ON THE FRAMING PLAN DRAWINGS WHERE ARE THE MEASUREMENTS TAKEN
BETWEEN ANY TWO COLUMNS? - ans -CENTER TO CENTER
WHAT IS THE MINIMUM...PERMITTED FROM THE CENTER OF ANY... COLUMN
LINE...? - ans -1/8"
IN ORDER TO WELD ON A JOBSITE A PERSON MUST - ans -PASS A WELDING
PERFORMANCE TEST.
, AN EXTENSION THAT PROJECTS FROM THE MAIN BODY OF THE CRANE TO ADD
STABILITY AND SUPPORT IS CALLED A(N): - ans -OUTRIGGER
WHEN A LOAD IS APPLIED TO ANY POINT ON A STEEL BEAM WHICH PART OF
THE... DISTRIBUTES THE LOAD TO OTHER PARTS OF...? - ans -BOTTOM CHORD
DURING THE INITIAL LIFTING OF A TRUSS. WHAT IS THE NAME OF THE TMPORARY
MEMBER ATTACEHD TO THE SIDE OF A TRUSS TO PROVIDE LATERAL SUPPORT? -
ans -STRONG BACK
LEVELING NUTS ARE USED TO: - ans -BEAR THE WEIGHT OF THE FRAME UNTIL THE
COLUMN BASES ARE GROUNDED
ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE
BOLT REQUIRED FOR A 3/4" DIAMETER BOLT? - ans -2 1/4"
THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE: - ans -SPAN
BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION
MUST BE COMPLETED? - ans -JOIST MUST HAVE BRIDGING INSTALLED
WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED
TO: - ans -HELP CONTROL THE LOAD
ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION
DETAILS ARE GENERALLY FOUND ON: - ans -THE DETAIL DRAWINGS
THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO RESIST PULLING FORCES IS
KNOWN AS: - ans -TENSILE STRENGHT
WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS RIB? - ans -
COMPOSITE DECK
THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE ROOF TOP
ELEVATION IS SHOWN AS +130.50. WHAT IS THE DIFFERENCE IN ELEVATION? - ans
-30'3
verified questions covering structural steel installation,
rigging and welding techniques, blueprint reading, safety
procedures, rebar placement, and construction site
protocols. Aligned with NCCER
WHEN AN EXTENSION BOOM IS USED ON A FORKLIFT IT CHANGES ITS: - ans -
CENTER OF GRAVITY
WHERE DOES THE FLUX COME FROM ON A SHEAR STUD? - ans -NIPPLE ON THE
BOTTOM OF THE STUD
WHICH OF THE FOLLOWING WELDING PROCESSES IS NOT TYPICALLY USED IN
STRUCTURAL STEEL APPLICATIONS? - ans -OXY-ACETYLENE WELDING
WHICH OF THE FOLLOWING IS A COMMON TYPE OF ELECTRONIC DISTANCE
MEASUREMENT INSTUMENT? - ans -LASER LIGHT
WHAT STUD WELDING PROCESS IS USED TO INSTALL COMPOSITE CONSTRUCTION
SHEAR STUDS? - ans -GTAW
BEFORE SPREADER BAR OR BEAMS CAN BE USED, THEY MUST HAVE BEEN - ans -
PROPERLY TESTED AND STAMPED
WHEN USING TWO SLINGS TO HOIST A BUNDLE OF LIGHT STEEL MATERIAL, THE
SLINGS SHOULD BE LOOPED IN THE SAME DIRECTION TO PREVENT - ans -
TWISTING OF THE BUNDLE
ON THE FRAMING PLAN DRAWINGS WHERE ARE THE MEASUREMENTS TAKEN
BETWEEN ANY TWO COLUMNS? - ans -CENTER TO CENTER
WHAT IS THE MINIMUM...PERMITTED FROM THE CENTER OF ANY... COLUMN
LINE...? - ans -1/8"
IN ORDER TO WELD ON A JOBSITE A PERSON MUST - ans -PASS A WELDING
PERFORMANCE TEST.
, AN EXTENSION THAT PROJECTS FROM THE MAIN BODY OF THE CRANE TO ADD
STABILITY AND SUPPORT IS CALLED A(N): - ans -OUTRIGGER
WHEN A LOAD IS APPLIED TO ANY POINT ON A STEEL BEAM WHICH PART OF
THE... DISTRIBUTES THE LOAD TO OTHER PARTS OF...? - ans -BOTTOM CHORD
DURING THE INITIAL LIFTING OF A TRUSS. WHAT IS THE NAME OF THE TMPORARY
MEMBER ATTACEHD TO THE SIDE OF A TRUSS TO PROVIDE LATERAL SUPPORT? -
ans -STRONG BACK
LEVELING NUTS ARE USED TO: - ans -BEAR THE WEIGHT OF THE FRAME UNTIL THE
COLUMN BASES ARE GROUNDED
ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE
BOLT REQUIRED FOR A 3/4" DIAMETER BOLT? - ans -2 1/4"
THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE: - ans -SPAN
BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION
MUST BE COMPLETED? - ans -JOIST MUST HAVE BRIDGING INSTALLED
WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED
TO: - ans -HELP CONTROL THE LOAD
ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION
DETAILS ARE GENERALLY FOUND ON: - ans -THE DETAIL DRAWINGS
THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO RESIST PULLING FORCES IS
KNOWN AS: - ans -TENSILE STRENGHT
WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS RIB? - ans -
COMPOSITE DECK
THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE ROOF TOP
ELEVATION IS SHOWN AS +130.50. WHAT IS THE DIFFERENCE IN ELEVATION? - ans
-30'3
