TTT1 STUDY GUIDE|90 QUESTIONS FOR
GUARANTEED SUCCESS / NEWEST 2025/2026.
1. Who is the third party group that approves and endorses standards? ANS
Amer- ican National Standards Institute
2. What term is used to describe the documents written by members, or peers,
in the industry? ANS Standards
3. A company's health, safety and environment policy should be a combination
of labor regulations and ? ANS Industry standards
4. Where OSHA has not promulgated specific standards, who is responsible
for following the acts general clause? ANS Employer
5. On a job site who should be involved in the JHA process? ANS The Whole
Crew
6. What does the Term SOW stand for? ANS Scope Of Work
7. The letters JHA stand for what ? ANS Job Hazard Assessment
8. When using a extension ladder, how many feet past the platform must it
extend? ANS 3
9. If you have a sixteen foot ladder leaning against a building wall, how many
feet from the wall does the case need to by to have the correct slope? ANS
4
https://www.stuvia.com/en-us/user/MBOFFIN 1/9
, 10. Work boots with ankle support are recommended for all work sites? ANS
True
11. What do the letters PPE stand for ? ANS Personal Protective Equipment
12. What does the ground fault circuit interrupter (GFCI) do? ANS Senses a
short circuit, prevents electrocution , shuts off the flow of electricity
13. Who is responsible for providing PPE? ANS Employer
14. When using a y-lanyard attached to your back d-ring, at what height should
the connection to your anchorage be placed?extend? ANS Shoulder level or
above
15. What is the maximum distance between the sternal d-ring and the fixed
safety climb? ANS Nine inches
16. When calculating a fall distance using a "6 foot" energy absorbed, what is
the maximum pull out distance? ANS Four feey
17. What is the minimum force that a work positioning system anchorage must
be able to withstand? ANS Two times the arresting force of 3000lbs
18. What minimum force must a non-engineered anchor be able to withstand
for fall protection use? ANS 5,000 lbs
19. When working, how often should fall protection equipment be inspected
? ANS Daily before each use
20. According to the applicable industry standard, what is the minimum height
from a lower surface or ground where fall protection must be used? ANS Six
feet
21. How many pounds force is one kilo Newton(kN) ANS 225
22. What are the four most common types of towers used to support telecom-
munications antennas? ANS Guyed towers, self-support towers, monopoles, and
non- standard
23. What identifies a self-support tower? ANS Horizontal member
https://www.stuvia.com/en-us/user/MBOFFIN 2/9
GUARANTEED SUCCESS / NEWEST 2025/2026.
1. Who is the third party group that approves and endorses standards? ANS
Amer- ican National Standards Institute
2. What term is used to describe the documents written by members, or peers,
in the industry? ANS Standards
3. A company's health, safety and environment policy should be a combination
of labor regulations and ? ANS Industry standards
4. Where OSHA has not promulgated specific standards, who is responsible
for following the acts general clause? ANS Employer
5. On a job site who should be involved in the JHA process? ANS The Whole
Crew
6. What does the Term SOW stand for? ANS Scope Of Work
7. The letters JHA stand for what ? ANS Job Hazard Assessment
8. When using a extension ladder, how many feet past the platform must it
extend? ANS 3
9. If you have a sixteen foot ladder leaning against a building wall, how many
feet from the wall does the case need to by to have the correct slope? ANS
4
https://www.stuvia.com/en-us/user/MBOFFIN 1/9
, 10. Work boots with ankle support are recommended for all work sites? ANS
True
11. What do the letters PPE stand for ? ANS Personal Protective Equipment
12. What does the ground fault circuit interrupter (GFCI) do? ANS Senses a
short circuit, prevents electrocution , shuts off the flow of electricity
13. Who is responsible for providing PPE? ANS Employer
14. When using a y-lanyard attached to your back d-ring, at what height should
the connection to your anchorage be placed?extend? ANS Shoulder level or
above
15. What is the maximum distance between the sternal d-ring and the fixed
safety climb? ANS Nine inches
16. When calculating a fall distance using a "6 foot" energy absorbed, what is
the maximum pull out distance? ANS Four feey
17. What is the minimum force that a work positioning system anchorage must
be able to withstand? ANS Two times the arresting force of 3000lbs
18. What minimum force must a non-engineered anchor be able to withstand
for fall protection use? ANS 5,000 lbs
19. When working, how often should fall protection equipment be inspected
? ANS Daily before each use
20. According to the applicable industry standard, what is the minimum height
from a lower surface or ground where fall protection must be used? ANS Six
feet
21. How many pounds force is one kilo Newton(kN) ANS 225
22. What are the four most common types of towers used to support telecom-
munications antennas? ANS Guyed towers, self-support towers, monopoles, and
non- standard
23. What identifies a self-support tower? ANS Horizontal member
https://www.stuvia.com/en-us/user/MBOFFIN 2/9
