5/22/25, 11:11 PM Final Exam Elevator | NEIEP 100 Elevator Final Exam/ 160 Quizzes with Definitive Solutions
Final Exam Elevator | NEIEP 100 Elevator Final
Exam/ 160 Quizzes with Definitive Solutions
ALREADY GRADED A+\VERIFIED ANSWERS
wrench used for rail spud wrench
installation
The minimum clearance a. 80"
form the floor to the
suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2"
what should you be aware b. The original weight and counterbalancing.
of when removing a cab
for replacement?
a. The weight that is to be
removed from the ceiling.
b. The original weight and
counterbalancing.
c. How much the cab was
out of square.
d. Cover the panels so
they do not get banged
up.
… 1/46
,5/22/25, 11:11 PM Final Exam Elevator | NEIEP 100 Elevator Final Exam/ 160 Quizzes with Definitive Solutions
When fans are used on d. They sWhould direct the fumes to the outside.
modernization jobs for
exhausting fumes, what
statement is correct?
a. They're to keep you
cool, not for exhausting
fumes.
b. They should direct the
fumes into the hoistway.
c. They should direct the
fumes into the pit.
d. They should direct the
fumes to the outside.
The star symbol is used on b. To designate the main floor.
the COP for what?
a. To show where the floor
buttons are located.
b. To designate the main
floor.
c. To make the door
buttons stand out.
d. To show the alarm bell
location.
Using a laminate stop strip c. Keeps the laminate from slipping under the fence.
against the fence on a
table saw:
a. Keeps the laminate
straight to the blade.
b. Keeps the laminate from
lifting off the blade.
c. Keeps the laminate from
slipping under the fence.
d. Keeps the laminate
from going over the fence.
… 2/46
,5/22/25, 11:11 PM Final Exam Elevator | NEIEP 100 Elevator Final Exam/ 160 Quizzes with Definitive Solutions
The contact adhesives b. Dry
must be ____ before final
bonding:
a. 85 degrees
b. Dry
c. Wet to touch
d. Cold
What is the most b. safety glasses
important piece of
equipment you have when
using a power saw?
a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square
When using a circular saw, a. Never start the cut until the blade is turning full
which of the following is RPM
correct?
a. Never start the cut until
the blade is turning full
RPM
b. The base is not
adjustable for cutting
depth
c. Circular saw blades
range from 10 to 16 inches
d. Remove the retractable
guard before cutting
What is used to make c. Miter saw
crosscuts on a table saw?
a. Push stick
b. Rip fence
c. Miter gauge
d. Larger Blade
… 3/46
, 5/22/25, 11:11 PM Final Exam Elevator | NEIEP 100 Elevator Final Exam/ 160 Quizzes with Definitive Solutions
When making crosscuts b. Restrain the blade from moving too fast
with a radial arm saw
which statement is
correct?
a. Push the wood slowly
into the blade.
b. Restrain the blade from
moving too fast.
c. Rotate and lock the
blade parallel to the
guide.
d. Adjust the blade 1/4"
above to cutting surface
What are the two things a d. bevel and mitre cuts can be made at the same time
compound mitre saw does
best at the same time?
a. moving it around and
setting it up is fast.
b. You can cut left and
right at the same time.
c. Tilting the blade 45
degrees and pivoting the
table 45 degrees gives
you a 90 degree square
cut.
d. bevel and mitre cuts
can be made at the same
time
… 4/46
Final Exam Elevator | NEIEP 100 Elevator Final
Exam/ 160 Quizzes with Definitive Solutions
ALREADY GRADED A+\VERIFIED ANSWERS
wrench used for rail spud wrench
installation
The minimum clearance a. 80"
form the floor to the
suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2"
what should you be aware b. The original weight and counterbalancing.
of when removing a cab
for replacement?
a. The weight that is to be
removed from the ceiling.
b. The original weight and
counterbalancing.
c. How much the cab was
out of square.
d. Cover the panels so
they do not get banged
up.
… 1/46
,5/22/25, 11:11 PM Final Exam Elevator | NEIEP 100 Elevator Final Exam/ 160 Quizzes with Definitive Solutions
When fans are used on d. They sWhould direct the fumes to the outside.
modernization jobs for
exhausting fumes, what
statement is correct?
a. They're to keep you
cool, not for exhausting
fumes.
b. They should direct the
fumes into the hoistway.
c. They should direct the
fumes into the pit.
d. They should direct the
fumes to the outside.
The star symbol is used on b. To designate the main floor.
the COP for what?
a. To show where the floor
buttons are located.
b. To designate the main
floor.
c. To make the door
buttons stand out.
d. To show the alarm bell
location.
Using a laminate stop strip c. Keeps the laminate from slipping under the fence.
against the fence on a
table saw:
a. Keeps the laminate
straight to the blade.
b. Keeps the laminate from
lifting off the blade.
c. Keeps the laminate from
slipping under the fence.
d. Keeps the laminate
from going over the fence.
… 2/46
,5/22/25, 11:11 PM Final Exam Elevator | NEIEP 100 Elevator Final Exam/ 160 Quizzes with Definitive Solutions
The contact adhesives b. Dry
must be ____ before final
bonding:
a. 85 degrees
b. Dry
c. Wet to touch
d. Cold
What is the most b. safety glasses
important piece of
equipment you have when
using a power saw?
a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square
When using a circular saw, a. Never start the cut until the blade is turning full
which of the following is RPM
correct?
a. Never start the cut until
the blade is turning full
RPM
b. The base is not
adjustable for cutting
depth
c. Circular saw blades
range from 10 to 16 inches
d. Remove the retractable
guard before cutting
What is used to make c. Miter saw
crosscuts on a table saw?
a. Push stick
b. Rip fence
c. Miter gauge
d. Larger Blade
… 3/46
, 5/22/25, 11:11 PM Final Exam Elevator | NEIEP 100 Elevator Final Exam/ 160 Quizzes with Definitive Solutions
When making crosscuts b. Restrain the blade from moving too fast
with a radial arm saw
which statement is
correct?
a. Push the wood slowly
into the blade.
b. Restrain the blade from
moving too fast.
c. Rotate and lock the
blade parallel to the
guide.
d. Adjust the blade 1/4"
above to cutting surface
What are the two things a d. bevel and mitre cuts can be made at the same time
compound mitre saw does
best at the same time?
a. moving it around and
setting it up is fast.
b. You can cut left and
right at the same time.
c. Tilting the blade 45
degrees and pivoting the
table 45 degrees gives
you a 90 degree square
cut.
d. bevel and mitre cuts
can be made at the same
time
… 4/46
