PIPE FITTER TEST QUESTIONS AND ANSWERS
What does TE in TE-601 stand for? - Answers :temperature element
what does B.T.U stand for? - Answers :British Thermal Unit
what is the boiling point of water? - Answers :212*F
What is 3.1416? - Answers :Pi
what is the circumference of a 15" pipe? (to the nearest tenth0 - Answers :47"
4" in the hundredths of a foot is? - Answers :.33
what is the take off for a 4" x 3" LR reducing 90* ell? - Answers :6"
on isometric drawings what does RFWN mean? - Answers :raised face weld neck
what does the Pi in Pi-209 stand for? - Answers :pressure indicator
101.25' converted into inches is what? - Answers :101'-3"
if testing the shell side of an exchanger with the flat cap removed and all the tubes on
the bottom row had a steady flow of water pouring out of them, this would indicate: -
Answers :floating head gasket leaking
3/4" is equal to? - Answers :6/8
the lap joint flange is usually used when_______? - Answers :flange hold alignment is a
problem
what is the number of a square feet in the surface of a steel plate 180 inches high and
48 inches wide? - Answers :60 square feet
what device is installed between a control valve and the air supply header? - Answers
:regulator
what is the most common degree of bevel on a pipe to be butt welded? - Answers :37
1/2
the three states of matter are: - Answers :solids, liquids,and gases
what is the circumference of a circle that has a 20.50 inch diameter? - Answers :64.37
extension lines should: - Answers :always touch the object being drawn
, what is 23% of 1598? - Answers :367.54
what is the circumference of a circle with a diameter of 5" - Answers :15.70"
what is the area of a triangle that is 30.5 feet long and 15 feet wide? (A=WxL) - Answers
:457.5 square feet
a globe valve is used to: - Answers :prevent flow in more than one direction
what would be the take off for a 45 standard 3" pipe ells? - Answers :4"
when using orifice flanges in a vapor service, the taps should be facing: - Answers :up
what dies T.O.E stand for? - Answers :thread one end
what does BLETSE stand for? - Answers :bevel large end/thread small end
tools that require hearing protection when used are: - Answers :chipping gun, side
grinder, air impact
items to look for on a bench grinder before use are: - Answers :cracked wheel, tool rest
within "1/8" of wheel, tongue guard attatched
if you wanted to reduce in a line but keep the same center line, you would use an
eccentric reducer - Answers :false
the 2 most commonly used types of tubing connections are compression and flared. -
Answers :true
a pressure indicator is indicated by a Pi symbol on a flow chart - Answers :true
a pressure indicator is indicated by a PI symbol on a flow chart - Answers :true
spray painting or modifying hard hats may damage them - Answers :true
pipe stamped with 316L and 304L denotes a grade or type of a carbon steel pipe and
fittings. - Answers :false
flange insulators Kits are installed for a cathodic protection - Answers :true
the proper way to lift is bend at your knees and let you legs do the lifting - Answers :true
exposure to high level noises can be controlled - Answers :true
to reduce chances of heat stress you should drink plenty of beet and alcohol - Answers
:false
What does TE in TE-601 stand for? - Answers :temperature element
what does B.T.U stand for? - Answers :British Thermal Unit
what is the boiling point of water? - Answers :212*F
What is 3.1416? - Answers :Pi
what is the circumference of a 15" pipe? (to the nearest tenth0 - Answers :47"
4" in the hundredths of a foot is? - Answers :.33
what is the take off for a 4" x 3" LR reducing 90* ell? - Answers :6"
on isometric drawings what does RFWN mean? - Answers :raised face weld neck
what does the Pi in Pi-209 stand for? - Answers :pressure indicator
101.25' converted into inches is what? - Answers :101'-3"
if testing the shell side of an exchanger with the flat cap removed and all the tubes on
the bottom row had a steady flow of water pouring out of them, this would indicate: -
Answers :floating head gasket leaking
3/4" is equal to? - Answers :6/8
the lap joint flange is usually used when_______? - Answers :flange hold alignment is a
problem
what is the number of a square feet in the surface of a steel plate 180 inches high and
48 inches wide? - Answers :60 square feet
what device is installed between a control valve and the air supply header? - Answers
:regulator
what is the most common degree of bevel on a pipe to be butt welded? - Answers :37
1/2
the three states of matter are: - Answers :solids, liquids,and gases
what is the circumference of a circle that has a 20.50 inch diameter? - Answers :64.37
extension lines should: - Answers :always touch the object being drawn
, what is 23% of 1598? - Answers :367.54
what is the circumference of a circle with a diameter of 5" - Answers :15.70"
what is the area of a triangle that is 30.5 feet long and 15 feet wide? (A=WxL) - Answers
:457.5 square feet
a globe valve is used to: - Answers :prevent flow in more than one direction
what would be the take off for a 45 standard 3" pipe ells? - Answers :4"
when using orifice flanges in a vapor service, the taps should be facing: - Answers :up
what dies T.O.E stand for? - Answers :thread one end
what does BLETSE stand for? - Answers :bevel large end/thread small end
tools that require hearing protection when used are: - Answers :chipping gun, side
grinder, air impact
items to look for on a bench grinder before use are: - Answers :cracked wheel, tool rest
within "1/8" of wheel, tongue guard attatched
if you wanted to reduce in a line but keep the same center line, you would use an
eccentric reducer - Answers :false
the 2 most commonly used types of tubing connections are compression and flared. -
Answers :true
a pressure indicator is indicated by a Pi symbol on a flow chart - Answers :true
a pressure indicator is indicated by a PI symbol on a flow chart - Answers :true
spray painting or modifying hard hats may damage them - Answers :true
pipe stamped with 316L and 304L denotes a grade or type of a carbon steel pipe and
fittings. - Answers :false
flange insulators Kits are installed for a cathodic protection - Answers :true
the proper way to lift is bend at your knees and let you legs do the lifting - Answers :true
exposure to high level noises can be controlled - Answers :true
to reduce chances of heat stress you should drink plenty of beet and alcohol - Answers
:false
