IRONWORKER NCCER QUESTIONS AND ANSWERS
100% GUARANTEED PASS!
THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO
RESIST PULLING FORCES IS KNOWN AS: - ANSWER -TENSILE
STRENGHT
WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS
RIB? - ANSWER -COMPOSITE DECK
THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE
ROOF TOP ELEVATION IS SHOWN AS +130.50. WHAT IS THE
DIFFERENCE IN ELEVATION? - ANSWER -30'3
IN WHAT DRAWING WOULD ONE FIND THE CORRECT BOLT
SIZE FOR A BEAM BEING BOLTED? - ANSWER -DETAIL
DRAWING
WHAT SHOULD ALWAYS BE USED TO IGNITE A CUTTING
TORCH? - ANSWER -STRIKER
EQUILIZING THE WEIGHT OF THE LOAD AT VARIOUS
LIFTING POINTS IS CALLED: - ANSWER -CONFIGURATION
A COMBINATION SQUARE WITHOUT A PROTRACTOR HEAD
IS USED TO LAYOUT: - ANSWER -45 DEGREE LINES
PRIOR TO INSPECTION IT IS GOOD PRACTICE TO TEST ALL
STUDS WITH WHAT METHOD? - ANSWER -PING TEST
, WHERE IS THE FULCRUM OR PIVOT POINT ON A FORKLIFT? -
ANSWER -THE FRONT AXLE
A DOCUMENT THAT OUTLINES WEIGHTS,CRANE
CONFIGURATION AND RIGGING REQUIREMENTS FOR A LIFT
IS CALLED AN: - ANSWER -LIFT PLAN
WHERE CAN THE BOLTING METHODS REGARDING
STRUCTURAL STEEL USUALLY BE FOUND ? - ANSWER -IN
THE GENERAL NOTES OF THE STRUCTURAL DRAWINGS
WHEN ESTABLISHING ELEVATIONS OF STRUCTURAL STEEL
MEMBERS, THE REFERENCE POINT USED TO DETERMINE ALL
OTHER ELEVATIONS IS CALLED? - ANSWER -THE
BENCHMARK
WHAT IS THE SURFACE AREA OF A RECTANGLE WITH THE
DIMENSIONS OF 30'6" TALL AND 6 FEET WIDE? - ANSWER -
183FT
MEASUREMENTS FROM THE CENTER OF THE CRANES AXIS
OF ROTATION TO THE CENTER OF THE LOAD LINE WITH THE
LOAD APPLIED IS: - ANSWER -LOAD RADIUS
WHICH OF THE FOLLOWING TOOLS WOULD BE USED TO PRY
STEEL INTO PLACE? - ANSWER -SLEEVER BAR
WHEN TRAVELING TO PICK UP A LOAD ALWAYS KEEP THE: -
ANSWER -FORKS LOW
100% GUARANTEED PASS!
THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO
RESIST PULLING FORCES IS KNOWN AS: - ANSWER -TENSILE
STRENGHT
WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS
RIB? - ANSWER -COMPOSITE DECK
THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE
ROOF TOP ELEVATION IS SHOWN AS +130.50. WHAT IS THE
DIFFERENCE IN ELEVATION? - ANSWER -30'3
IN WHAT DRAWING WOULD ONE FIND THE CORRECT BOLT
SIZE FOR A BEAM BEING BOLTED? - ANSWER -DETAIL
DRAWING
WHAT SHOULD ALWAYS BE USED TO IGNITE A CUTTING
TORCH? - ANSWER -STRIKER
EQUILIZING THE WEIGHT OF THE LOAD AT VARIOUS
LIFTING POINTS IS CALLED: - ANSWER -CONFIGURATION
A COMBINATION SQUARE WITHOUT A PROTRACTOR HEAD
IS USED TO LAYOUT: - ANSWER -45 DEGREE LINES
PRIOR TO INSPECTION IT IS GOOD PRACTICE TO TEST ALL
STUDS WITH WHAT METHOD? - ANSWER -PING TEST
, WHERE IS THE FULCRUM OR PIVOT POINT ON A FORKLIFT? -
ANSWER -THE FRONT AXLE
A DOCUMENT THAT OUTLINES WEIGHTS,CRANE
CONFIGURATION AND RIGGING REQUIREMENTS FOR A LIFT
IS CALLED AN: - ANSWER -LIFT PLAN
WHERE CAN THE BOLTING METHODS REGARDING
STRUCTURAL STEEL USUALLY BE FOUND ? - ANSWER -IN
THE GENERAL NOTES OF THE STRUCTURAL DRAWINGS
WHEN ESTABLISHING ELEVATIONS OF STRUCTURAL STEEL
MEMBERS, THE REFERENCE POINT USED TO DETERMINE ALL
OTHER ELEVATIONS IS CALLED? - ANSWER -THE
BENCHMARK
WHAT IS THE SURFACE AREA OF A RECTANGLE WITH THE
DIMENSIONS OF 30'6" TALL AND 6 FEET WIDE? - ANSWER -
183FT
MEASUREMENTS FROM THE CENTER OF THE CRANES AXIS
OF ROTATION TO THE CENTER OF THE LOAD LINE WITH THE
LOAD APPLIED IS: - ANSWER -LOAD RADIUS
WHICH OF THE FOLLOWING TOOLS WOULD BE USED TO PRY
STEEL INTO PLACE? - ANSWER -SLEEVER BAR
WHEN TRAVELING TO PICK UP A LOAD ALWAYS KEEP THE: -
ANSWER -FORKS LOW
