SACA Study ExAm with AnSwErS 100%
CorrECt
What is the range by which a part dimension may vary called? ANSWER -> Tolerance
What should you do if a machine safety guard has been bypassed? ANSWER -> Lock out the
machine and call the supervisor
What indicator on an operator panel will likely be on when the machine is in normal
production? ANSWER -> Single step
The highlighted area in the figure shown shows which type of view of the part? ANSWER ->
Sectional
What is the robot component shown? ANSWER -> Teach pendant
In addition to Medical and Environmental what is another category of emergency in a company?
ANSWER -> Hostile threats
What type of file determines the order in which a robot moves to points in the work envelope?
ANSWER -> Program
In this drawing of a two-part assembly, what is the type of fit if the shaft diameter is slightly
larger than the hole diameter? ANSWER -> Interference
What technology element differentiates Industry 4.0 from Industry 3.0? ANSWER -> Smart
sensors connected to network
,What type of manufacturing process to 3D printers perform? ANSWER -> Additive
What is the type of robot shown here? ANSWER -> SCARA
What is the proper operation sequence of the fire extinguisher? ANSWER -> Pull, aim, squeeze,
sweep
What is the pressure shown on this gauge?* ANSWER -> 500 kPa
What type of wrench is shown?* ANSWER -> Ratchet
What amount of power is used in this circuit?* ANSWER -> 96W
What type of geometric tolerance is shown in the feature control frame on this drawing?
ANSWER -> Circularity
A company's Emergency Action Plan (EAP) should include ALL of the following except? ANSWER
-> Machine operation procedures
What action must be taken to correctly position a dial caliper? ANSWER -> Sweep and rock to
the jaws
What type of hand tool has a cross-shaped head to engage and tighten a fastener?* ANSWER ->
Phillips head screwdriver
Which of these activities is considered non-value added activity in a lean manufacturing
environment?*
0/4 ANSWER -> Moving a product from one station to another
, What is the tolerance of the width of this part?* ANSWER -> +/-0.1
What do SDS sheets do?* ANSWER -> Specify material hazards.
When a click-type torque wrench clicks at the set point, what do you do to apply the proper
torque? ANSWER -> Stop turning the wrench
What type of hole is identified by the arrow labeled A?* ANSWER -> Blind
What component does the schematic represent?* ANSWER -> Pneumatic motor
What type of information would not normally be found in a drawing's title block?*
0/4 ANSWER -> General notes
What machine can be programmed to perform tasks in many different operations? ANSWER ->
Robot
What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 ANSWER -> metal
Which of these is NOT a primary goal of a lean manufacturing system? ANSWER -> Greater
production volume
In the bolt designation shown, what is the pitch? ANSWER -> 2.5
CorrECt
What is the range by which a part dimension may vary called? ANSWER -> Tolerance
What should you do if a machine safety guard has been bypassed? ANSWER -> Lock out the
machine and call the supervisor
What indicator on an operator panel will likely be on when the machine is in normal
production? ANSWER -> Single step
The highlighted area in the figure shown shows which type of view of the part? ANSWER ->
Sectional
What is the robot component shown? ANSWER -> Teach pendant
In addition to Medical and Environmental what is another category of emergency in a company?
ANSWER -> Hostile threats
What type of file determines the order in which a robot moves to points in the work envelope?
ANSWER -> Program
In this drawing of a two-part assembly, what is the type of fit if the shaft diameter is slightly
larger than the hole diameter? ANSWER -> Interference
What technology element differentiates Industry 4.0 from Industry 3.0? ANSWER -> Smart
sensors connected to network
,What type of manufacturing process to 3D printers perform? ANSWER -> Additive
What is the type of robot shown here? ANSWER -> SCARA
What is the proper operation sequence of the fire extinguisher? ANSWER -> Pull, aim, squeeze,
sweep
What is the pressure shown on this gauge?* ANSWER -> 500 kPa
What type of wrench is shown?* ANSWER -> Ratchet
What amount of power is used in this circuit?* ANSWER -> 96W
What type of geometric tolerance is shown in the feature control frame on this drawing?
ANSWER -> Circularity
A company's Emergency Action Plan (EAP) should include ALL of the following except? ANSWER
-> Machine operation procedures
What action must be taken to correctly position a dial caliper? ANSWER -> Sweep and rock to
the jaws
What type of hand tool has a cross-shaped head to engage and tighten a fastener?* ANSWER ->
Phillips head screwdriver
Which of these activities is considered non-value added activity in a lean manufacturing
environment?*
0/4 ANSWER -> Moving a product from one station to another
, What is the tolerance of the width of this part?* ANSWER -> +/-0.1
What do SDS sheets do?* ANSWER -> Specify material hazards.
When a click-type torque wrench clicks at the set point, what do you do to apply the proper
torque? ANSWER -> Stop turning the wrench
What type of hole is identified by the arrow labeled A?* ANSWER -> Blind
What component does the schematic represent?* ANSWER -> Pneumatic motor
What type of information would not normally be found in a drawing's title block?*
0/4 ANSWER -> General notes
What machine can be programmed to perform tasks in many different operations? ANSWER ->
Robot
What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 ANSWER -> metal
Which of these is NOT a primary goal of a lean manufacturing system? ANSWER -> Greater
production volume
In the bolt designation shown, what is the pitch? ANSWER -> 2.5
