MSSC Quality Practices & Measurement
Exam Questions And Answers
Which type of feature is parallel to the surface being dimensioned?
---
correct answer ✅Dimension line
The three standard views of an object are __________. - - -
correct answer ✅Top, front, right side
Which type of lines are used to show the counterbored hole in the
part? - - -
correct answer ✅Hidden lines
The number of views in a drawing __________. - - -
correct answer ✅Is the fewest number that shows all of the
features and dimensions
Which of the following steps is NOT used in the glass box method? -
--
correct answer ✅Rotate object in glass box.
What type of drawing is shown? - - -
correct answer ✅Multiview
,MSSC Quality Practices & Measurement
Exam Questions And Answers
The dimensions of raw material supplied by metal suppliers are
described by the __________. - - -
correct answer ✅Stock size
Which of these requires a computer? - - -
correct answer ✅CAD
An isometric drawing is a type of __________. - - -
correct answer ✅Pictorial drawing
In the graphic shown, the two circles are __________. - - -
correct answer ✅Concentric
Dimensions are used to specify the __________ and location of the
features of an object. - - -
correct answer ✅Size
What feature in the figure shown is a Chamfer? - - -
correct answer ✅D
,MSSC Quality Practices & Measurement
Exam Questions And Answers
A __________ dimension is described in inches per foot. - - -
correct answer ✅Shaft taper
What is the order of precedence of lines in a drawing? - - -
correct answer ✅Object, Hidden, Center
Which of the following is not one of the six rules for dimensioning
an object? - - -
correct answer ✅Dimension hidden lines
Engineers sometimes use a __________ to measure angles on a
drawing. - - -
correct answer ✅Protractor
What dimension is indicated in this graphic? - - -
correct answer ✅Height
There are 60 minutes of arc in one __________. - - -
correct answer ✅Degree
, MSSC Quality Practices & Measurement
Exam Questions And Answers
In manufacturing, a blueprint is also called what? - - -
correct answer ✅A technical drawing
The distance across the flats of the hex head shown in the part
drawing is __________ inches. - - -
correct answer ✅2 ¼
The length of the part shown in the drawing is __________ inches. -
--
correct answer ✅9 ¾
Which type best describes the line indicated in the graphic? - - -
correct answer ✅Object Line
Which of the following bolts is a grade 2? - - -
correct answer ✅A
The hole shown in the graphic is a __________ hole. - - -
correct answer ✅Counterbore
Exam Questions And Answers
Which type of feature is parallel to the surface being dimensioned?
---
correct answer ✅Dimension line
The three standard views of an object are __________. - - -
correct answer ✅Top, front, right side
Which type of lines are used to show the counterbored hole in the
part? - - -
correct answer ✅Hidden lines
The number of views in a drawing __________. - - -
correct answer ✅Is the fewest number that shows all of the
features and dimensions
Which of the following steps is NOT used in the glass box method? -
--
correct answer ✅Rotate object in glass box.
What type of drawing is shown? - - -
correct answer ✅Multiview
,MSSC Quality Practices & Measurement
Exam Questions And Answers
The dimensions of raw material supplied by metal suppliers are
described by the __________. - - -
correct answer ✅Stock size
Which of these requires a computer? - - -
correct answer ✅CAD
An isometric drawing is a type of __________. - - -
correct answer ✅Pictorial drawing
In the graphic shown, the two circles are __________. - - -
correct answer ✅Concentric
Dimensions are used to specify the __________ and location of the
features of an object. - - -
correct answer ✅Size
What feature in the figure shown is a Chamfer? - - -
correct answer ✅D
,MSSC Quality Practices & Measurement
Exam Questions And Answers
A __________ dimension is described in inches per foot. - - -
correct answer ✅Shaft taper
What is the order of precedence of lines in a drawing? - - -
correct answer ✅Object, Hidden, Center
Which of the following is not one of the six rules for dimensioning
an object? - - -
correct answer ✅Dimension hidden lines
Engineers sometimes use a __________ to measure angles on a
drawing. - - -
correct answer ✅Protractor
What dimension is indicated in this graphic? - - -
correct answer ✅Height
There are 60 minutes of arc in one __________. - - -
correct answer ✅Degree
, MSSC Quality Practices & Measurement
Exam Questions And Answers
In manufacturing, a blueprint is also called what? - - -
correct answer ✅A technical drawing
The distance across the flats of the hex head shown in the part
drawing is __________ inches. - - -
correct answer ✅2 ¼
The length of the part shown in the drawing is __________ inches. -
--
correct answer ✅9 ¾
Which type best describes the line indicated in the graphic? - - -
correct answer ✅Object Line
Which of the following bolts is a grade 2? - - -
correct answer ✅A
The hole shown in the graphic is a __________ hole. - - -
correct answer ✅Counterbore
