J-STD-001 || with 100% Verified Solutions.

J-STD-001 || with 100% Verified Solutions.
Who is responsible for identifying the assembly class? correct answers User

What is a defect? correct answers A condition that may affect the form, fit, or function of the
item in the end use environment

Hardware found to not conform to the requirements of the standard shall be classified as defects
and dispositioned for: correct answers [D1D2D3]

There shall be no broken strands for wires used at a potential of 6kV or greater: correct answers
[D1D2D3]

A documented process control system shall be implemented for: correct answers [N1N2D3]

The contract shall take precedence over this standard for: correct answers [D1D2D3]

What is wire overlap? correct answers When a wire is wrapped more than 360 and crosses over
itself

What is wire over wrap? correct answers When a wire is wrapped more than 360 and remains in
contact with the terminal

Manufacturers shall perform 100% inspection unless sampling inspection is defined for: correct
answers [N1D2D3]

Inspection of soldering and cleanliness shall be performed prior to conformal coasting, staking,
or encapsulation for: correct answers [N1D2D3]

Illumination at the surface of work stations should be at least what? correct answers 1000 lux

What is the tolerance for magnification aids? correct answers +- 15%

Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: correct answers
[D1D2D3]

Manufacturer shall verify ESD is adequate when humidity falls below 30% for: correct answers
[N1D2D3]

Manufacturer shall establish an ESD control program for: correct answers [D1D2D3]

What is J-STD-002? correct answers Solder-ability tests for Component leads, terminations,
lugs, wires, and terminals

What is J-STD-003? correct answers Solder ability tests for printed boards

, What is J-STD-004? correct answers Requirements for Soldering Fluxes

What is J-STD-005? correct answers Requirements for Soldering Paste

What is J-STD-006? correct answers Requirements for electronic grade solder alloys, fluxed and
non-fluxed solid solders

Manufacturers shall have a Pb-free control plan for: correct answers [N1N2D3]

Items exposed to uncured silicone material shall not be used for processing other material for:
correct answers [D1D2D3]

Solder alloys shall be in accordance with J-STD-006 or equivalent for: correct answers
[D1D2D3]

Solder paste shall be in accordance with J-STD-005 or equivalent for: correct answers
[D1D2D3]

Pb-free processing shall be in accordance with a documental procedure for: correct answers
[N1D2D3]

SnPb solder alloys other than ... shall be in compliance for: correct answers [N1D2D3]

Dross shall be removed from the solder surface without contacting tinned or soldered items for:
correct answers [N1D2D3]

Type H or M fluxes shall not be used for tinning of stranded wires for: correct answers
[D1D2D3]

Flux shall be in accordance with J-STD-004 or equivalent for: correct answers [D1D2D3]

Adhesives shall not be detrimental and shall be cured for: correct answers [D1D2D3]

Component coating meniscus shall not be trimmed for: correct answers [N1D2D3]

A tool used to cut leads shall not impart shock that damages something for: correct answers
[D1D2D3]

Loss of metallization as a result of processing shall not expose ceramic on terminal end face ...
for: correct answers [D1D2D3]

Strands wire shall not be tinned when wires will be used in forming mesh splices, crimp
termination, or threaded fasteners for: correct answers [D1D2D3]

Wire strands shall not be altered or cut to fit terminals for: correct answers [A1D2D3]