CDFA Weight Verification Practice Questions
And Answers New!!
Specifications are particularly directed to - ANSWER Manufacturers of devices
An axle load scale is normally - ANSWER permanently installed
what term does not apply to nose iron - ANSWER range
The term nominal as applied to a scale, measure, weight, etc. means - ANSWER
intended or stated value
A tare mechanism is used primarily for the purpose of - ANSWER balancing out the
weight of empty containers
Newly manufactured scales are required to be designated as - ANSWER Class I, II, III,
IIIL, or IIII
The normal valance position of the weighbeam of a beam scale shall be - ANSWER
horizontal
A county sealer/ director of W&M may, with the approval of the Secretary of Food and
Agriculture, use a frequency of inspection which is - ANSWER Different from
regulations
On a prescription scale that is equipped with a balance indicator, this indicator
consisting of an indicator and a graduated scale they are not in the same plane, the
clearance between the indicator and the graduations shall not be more than - ANSWER
0.04 inches
, Graduations of a scale beam shall be so varied in length that - ANSWER they may be
conveniently read
A poise stop is not required on a steelyard when - ANSWER there is no zero graduation
The adjusting material in a poise shall be fully enclosed and securely fastened in place
and it shall not touch the weigh beam, if softer than - ANSWER brass
The sensitivity requirement of a scale shall be applied in conjunction with - ANSWER
regardless of maintenance and acceptance tolerances
A variable frequency inspection plan shall provide for testing of all commercial devices
on - ANSWER regular frequency, variable frequency and statistical sampling
procedure
Each weighing device shall have at least one permanent and conspicuous identification
marking with what information - ANSWER Name, initials or trademark of the
manufacturer or distributor, model number, and non repetitive serial number
The graduated interval is - ANSWER distance from the center of one graduation to the
center of the next graduation in a graduated series
non retroactive means - ANSWER Only enforceable with respect to devices made after
implimentation
Meat beams, steelyards, portable platform, and belt conveyor scales all have a
frequency of inspection which is - ANSWER the same
the director may issue rules and regulations for - ANSWER device repairmen,
accuracy of commercial devices, and responsibilities of device repairmen
And Answers New!!
Specifications are particularly directed to - ANSWER Manufacturers of devices
An axle load scale is normally - ANSWER permanently installed
what term does not apply to nose iron - ANSWER range
The term nominal as applied to a scale, measure, weight, etc. means - ANSWER
intended or stated value
A tare mechanism is used primarily for the purpose of - ANSWER balancing out the
weight of empty containers
Newly manufactured scales are required to be designated as - ANSWER Class I, II, III,
IIIL, or IIII
The normal valance position of the weighbeam of a beam scale shall be - ANSWER
horizontal
A county sealer/ director of W&M may, with the approval of the Secretary of Food and
Agriculture, use a frequency of inspection which is - ANSWER Different from
regulations
On a prescription scale that is equipped with a balance indicator, this indicator
consisting of an indicator and a graduated scale they are not in the same plane, the
clearance between the indicator and the graduations shall not be more than - ANSWER
0.04 inches
, Graduations of a scale beam shall be so varied in length that - ANSWER they may be
conveniently read
A poise stop is not required on a steelyard when - ANSWER there is no zero graduation
The adjusting material in a poise shall be fully enclosed and securely fastened in place
and it shall not touch the weigh beam, if softer than - ANSWER brass
The sensitivity requirement of a scale shall be applied in conjunction with - ANSWER
regardless of maintenance and acceptance tolerances
A variable frequency inspection plan shall provide for testing of all commercial devices
on - ANSWER regular frequency, variable frequency and statistical sampling
procedure
Each weighing device shall have at least one permanent and conspicuous identification
marking with what information - ANSWER Name, initials or trademark of the
manufacturer or distributor, model number, and non repetitive serial number
The graduated interval is - ANSWER distance from the center of one graduation to the
center of the next graduation in a graduated series
non retroactive means - ANSWER Only enforceable with respect to devices made after
implimentation
Meat beams, steelyards, portable platform, and belt conveyor scales all have a
frequency of inspection which is - ANSWER the same
the director may issue rules and regulations for - ANSWER device repairmen,
accuracy of commercial devices, and responsibilities of device repairmen
