MSSC Quality Exam UPDATED Exam
Questions and CORRECT Answers
The dimensions of raw material supplied by metal suppliers are described by the __________. -
CORRECT ANSWER - stock size
Engineers sometimes use a ____________ to measure angles on a drawing. - CORRECT
ANSWER - Protractor
The three standard views of an object are____________. - CORRECT ANSWER - top,
front, right side
What type of drawing is shown? "All three views of an object." - CORRECT ANSWER -
Multiview
Which drafting style requires a computer? - CORRECT ANSWER - CAD
An isometric drawing is a type of _________? - CORRECT ANSWER - pictorial drawing
What dimension is indicated in the graphic? "Front view from bottom to top?" - CORRECT
ANSWER - Height
In manufacturing, a blueprint is also called what? - CORRECT ANSWER - a technical
drawing
Which of the following steps is not used in the glass box method? - CORRECT
ANSWER - Rotate object in a glass box
The number of views in a drawing __________. - CORRECT ANSWER - is the fewest
number that shows all the features and dimensions
,what is the order of precedence of lines in a drawing? - CORRECT ANSWER - object,
hidden, center
The holes to be drilled in the part are represented by _________. "Shows dashed lines through
part" - CORRECT ANSWER - Hidden lines
What type best describes the line in the graphic? "reversed capital L pointing at the outside
upright leg line." - CORRECT ANSWER - Object line
Dimensions are used to specify the _________ and location of the features of an object. -
CORRECT ANSWER - size
a _________ dimension is described in inches per foot. - CORRECT ANSWER - shaft
taper
there are 60 minutes of arc in one _________. - CORRECT ANSWER - degree
in the graphic shown, the two circles are _________. "there are two circles, one inside the other
the same plane and same distance apart around the circumference" - CORRECT
ANSWER - concentric
what features in the figure shown is a chamfer?
A- is a flat plane
b- seems to be an alignment pin
c- is a hidden hole
d-is the cut off edge of a 90 degree - CORRECT ANSWER - D.
which type of feature is parallel to the surface being dimensioned? - CORRECT
ANSWER - Dimension Line
, the length of the part shown in the drawing is _________ inches. "Lots of lines but look for the
overall lines" - CORRECT ANSWER - 9-3/4
which of the following is NOT one of the six rules for dimensioning and object?
a-do not over dimension
b-Dimension in the view that most clearly shows the feature
c-dimension hidden lines
d-dimension an object completely - CORRECT ANSWER - c-dimension hidden lines
The distance across the flats of the hex head shown in the part drawing is __________ inches.
"find the hex head and go from flat to flat. - CORRECT ANSWER - 2-1/4
the hole shown in the graphic is a(n) __________ hole. "shows a hole with a noticeable shoulder
passing completely through part" - CORRECT ANSWER - counterbore
What type hole is shown in the figure? "dashes lines show hole with a squared edge as it steps
down a size" - CORRECT ANSWER - counterbored
where would you look in a title block to see if there has been changes? - CORRECT
ANSWER - revision number
the material that will be used to create the gear is indicated in the part drawings title block to be
__________? "Look at the MATL: section" - CORRECT ANSWER - cast iron
to establish on a drawing that 1/4 inch equals 1 inch, the designer would write ___________. -
CORRECT ANSWER - 1/4=1
the feature on a drawing is drawn 3 inches long and the scale is 1:4, what is the actual dimension
on the object? - CORRECT ANSWER - 12"
Questions and CORRECT Answers
The dimensions of raw material supplied by metal suppliers are described by the __________. -
CORRECT ANSWER - stock size
Engineers sometimes use a ____________ to measure angles on a drawing. - CORRECT
ANSWER - Protractor
The three standard views of an object are____________. - CORRECT ANSWER - top,
front, right side
What type of drawing is shown? "All three views of an object." - CORRECT ANSWER -
Multiview
Which drafting style requires a computer? - CORRECT ANSWER - CAD
An isometric drawing is a type of _________? - CORRECT ANSWER - pictorial drawing
What dimension is indicated in the graphic? "Front view from bottom to top?" - CORRECT
ANSWER - Height
In manufacturing, a blueprint is also called what? - CORRECT ANSWER - a technical
drawing
Which of the following steps is not used in the glass box method? - CORRECT
ANSWER - Rotate object in a glass box
The number of views in a drawing __________. - CORRECT ANSWER - is the fewest
number that shows all the features and dimensions
,what is the order of precedence of lines in a drawing? - CORRECT ANSWER - object,
hidden, center
The holes to be drilled in the part are represented by _________. "Shows dashed lines through
part" - CORRECT ANSWER - Hidden lines
What type best describes the line in the graphic? "reversed capital L pointing at the outside
upright leg line." - CORRECT ANSWER - Object line
Dimensions are used to specify the _________ and location of the features of an object. -
CORRECT ANSWER - size
a _________ dimension is described in inches per foot. - CORRECT ANSWER - shaft
taper
there are 60 minutes of arc in one _________. - CORRECT ANSWER - degree
in the graphic shown, the two circles are _________. "there are two circles, one inside the other
the same plane and same distance apart around the circumference" - CORRECT
ANSWER - concentric
what features in the figure shown is a chamfer?
A- is a flat plane
b- seems to be an alignment pin
c- is a hidden hole
d-is the cut off edge of a 90 degree - CORRECT ANSWER - D.
which type of feature is parallel to the surface being dimensioned? - CORRECT
ANSWER - Dimension Line
, the length of the part shown in the drawing is _________ inches. "Lots of lines but look for the
overall lines" - CORRECT ANSWER - 9-3/4
which of the following is NOT one of the six rules for dimensioning and object?
a-do not over dimension
b-Dimension in the view that most clearly shows the feature
c-dimension hidden lines
d-dimension an object completely - CORRECT ANSWER - c-dimension hidden lines
The distance across the flats of the hex head shown in the part drawing is __________ inches.
"find the hex head and go from flat to flat. - CORRECT ANSWER - 2-1/4
the hole shown in the graphic is a(n) __________ hole. "shows a hole with a noticeable shoulder
passing completely through part" - CORRECT ANSWER - counterbore
What type hole is shown in the figure? "dashes lines show hole with a squared edge as it steps
down a size" - CORRECT ANSWER - counterbored
where would you look in a title block to see if there has been changes? - CORRECT
ANSWER - revision number
the material that will be used to create the gear is indicated in the part drawings title block to be
__________? "Look at the MATL: section" - CORRECT ANSWER - cast iron
to establish on a drawing that 1/4 inch equals 1 inch, the designer would write ___________. -
CORRECT ANSWER - 1/4=1
the feature on a drawing is drawn 3 inches long and the scale is 1:4, what is the actual dimension
on the object? - CORRECT ANSWER - 12"
