MSSC Quality Practices & Measurement
UPDATED Exam Questions and
CORRECT Answers
Which type of feature is parallel to the surface being dimensioned? - CORRECT
ANSWER - Dimension line
The three standard views of an object are __________. - CORRECT ANSWER - Top,
front, right side
Which type of lines are used to show the counterbored hole in the part? - CORRECT
ANSWER - Hidden lines
The number of views in a drawing __________. - CORRECT ANSWER - Is the fewest
number that shows all of the features and dimensions
Which of the following steps is NOT used in the glass box method? - CORRECT
ANSWER - Rotate object in glass box.
What type of drawing is shown? - CORRECT ANSWER - Multiview
The dimensions of raw material supplied by metal suppliers are described by the __________. -
CORRECT ANSWER - Stock size
Which of these requires a computer? - CORRECT ANSWER - CAD
An isometric drawing is a type of __________. - CORRECT ANSWER - Pictorial drawing
,In the graphic shown, the two circles are __________. - CORRECT ANSWER -
Concentric
Dimensions are used to specify the __________ and location of the features of an object. -
CORRECT ANSWER - Size
What feature in the figure shown is a Chamfer? - CORRECT ANSWER -D
A __________ dimension is described in inches per foot. - CORRECT ANSWER - Shaft
taper
What is the order of precedence of lines in a drawing? - CORRECT ANSWER - Object,
Hidden, Center
Which of the following is not one of the six rules for dimensioning an object? - CORRECT
ANSWER - Dimension hidden lines
Engineers sometimes use a __________ to measure angles on a drawing. - CORRECT
ANSWER - Protractor
What dimension is indicated in this graphic? - CORRECT ANSWER - Height
There are 60 minutes of arc in one __________. - CORRECT ANSWER - Degree
In manufacturing, a blueprint is also called what? - CORRECT ANSWER - A technical
drawing
The distance across the flats of the hex head shown in the part drawing is __________ inches. -
CORRECT ANSWER -2¼
, The length of the part shown in the drawing is __________ inches. - CORRECT
ANSWER -9¾
Which type best describes the line indicated in the graphic? - CORRECT ANSWER -
Object Line
Which of the following bolts is a grade 2? - CORRECT ANSWER -A
The hole shown in the graphic is a __________ hole. - CORRECT ANSWER -
Counterbore
What are the two types of assembly drawings? - CORRECT ANSWER - Exploded and
basic
A sectional view __________. - CORRECT ANSWER - All of the above
Which of the following is not used to specify a threaded fastener? - CORRECT
ANSWER - Minor diameter
Two types of threads are __________. - CORRECT ANSWER - Internal and external
In the assembly drawing shown, part 3 screws into part __________. - CORRECT
ANSWER -4
The material that will be used to create the gear is indicated in the part drawing's title block to be
__________. - CORRECT ANSWER - Cast iron
In a threaded fastener assembly what is designed to protect the threads? - CORRECT
ANSWER - Shank
UPDATED Exam Questions and
CORRECT Answers
Which type of feature is parallel to the surface being dimensioned? - CORRECT
ANSWER - Dimension line
The three standard views of an object are __________. - CORRECT ANSWER - Top,
front, right side
Which type of lines are used to show the counterbored hole in the part? - CORRECT
ANSWER - Hidden lines
The number of views in a drawing __________. - CORRECT ANSWER - Is the fewest
number that shows all of the features and dimensions
Which of the following steps is NOT used in the glass box method? - CORRECT
ANSWER - Rotate object in glass box.
What type of drawing is shown? - CORRECT ANSWER - Multiview
The dimensions of raw material supplied by metal suppliers are described by the __________. -
CORRECT ANSWER - Stock size
Which of these requires a computer? - CORRECT ANSWER - CAD
An isometric drawing is a type of __________. - CORRECT ANSWER - Pictorial drawing
,In the graphic shown, the two circles are __________. - CORRECT ANSWER -
Concentric
Dimensions are used to specify the __________ and location of the features of an object. -
CORRECT ANSWER - Size
What feature in the figure shown is a Chamfer? - CORRECT ANSWER -D
A __________ dimension is described in inches per foot. - CORRECT ANSWER - Shaft
taper
What is the order of precedence of lines in a drawing? - CORRECT ANSWER - Object,
Hidden, Center
Which of the following is not one of the six rules for dimensioning an object? - CORRECT
ANSWER - Dimension hidden lines
Engineers sometimes use a __________ to measure angles on a drawing. - CORRECT
ANSWER - Protractor
What dimension is indicated in this graphic? - CORRECT ANSWER - Height
There are 60 minutes of arc in one __________. - CORRECT ANSWER - Degree
In manufacturing, a blueprint is also called what? - CORRECT ANSWER - A technical
drawing
The distance across the flats of the hex head shown in the part drawing is __________ inches. -
CORRECT ANSWER -2¼
, The length of the part shown in the drawing is __________ inches. - CORRECT
ANSWER -9¾
Which type best describes the line indicated in the graphic? - CORRECT ANSWER -
Object Line
Which of the following bolts is a grade 2? - CORRECT ANSWER -A
The hole shown in the graphic is a __________ hole. - CORRECT ANSWER -
Counterbore
What are the two types of assembly drawings? - CORRECT ANSWER - Exploded and
basic
A sectional view __________. - CORRECT ANSWER - All of the above
Which of the following is not used to specify a threaded fastener? - CORRECT
ANSWER - Minor diameter
Two types of threads are __________. - CORRECT ANSWER - Internal and external
In the assembly drawing shown, part 3 screws into part __________. - CORRECT
ANSWER -4
The material that will be used to create the gear is indicated in the part drawing's title block to be
__________. - CORRECT ANSWER - Cast iron
In a threaded fastener assembly what is designed to protect the threads? - CORRECT
ANSWER - Shank
