EPA 608 Type III Exam Questions and Answers 100% Correct

EPA 608 Type III Exam Questions and Answers 100% Correct Identify the pressure corresponding to 32 degrees F for R-123: ________. a) 23 inches of Hg vacuum b) 20 inches of Hg vacuum c) 17 inches of Hg vacuum d) 11 inches of Hg vacuum - Answers b) 20 inches of Hg vacuum A hydrostatic tube test kit is used to: _________. a) blow all water from the tubes b) remove any water from the machine c) vent refrigerant d) determine if a tube leaks - Answers d) determine if a tube leaks Excessive running of a purge system on a low pressure chiller generally indicates that the: ___________. a) air sensors are faulty b) ambient temperature is too high c) efficiency of the purge unit is too low d) system is leaking - Answers d) system is leaking When recovering vapor from a low pressure refrigeration system: __________. a) water pumps should all be on, and the recovery compressor should be off b) system water pumps should be on, the recovery compressor should be on, and the recovery condenser water should be off c) the systems water pumps, the recovery compressor, and the recovery condenser water should all be on d) system water pumps should be off, and the recovery compressor should be on - Answers c) the systems water pumps, the recovery compressor, and the recovery condenser water should all be on ASHRAE Standard 15 - 1994 requires equipment room refrigerant sensors for what safety group classifications? a) A1 b) B2 c) A2 d) All refrigerant safety group classifications. - Answers d) All refrigerant safety group classifications If you are using a recovery machine manufactured BEFORE November 15, 1993, you must evacuate any low-pressure appliance to _______ before making a major repair. a) 0 psig b) 15 inches of Hg vacuum c) 25 inches of Hg vacuum d) 25mm of Hg absolute - Answers c) 25 inches of Hg vacuum A rupture disc on a recovery vessel for low pressure refrigerants relieves at: ________. a) 5 psig b) 10 psig c) 15 psig d) 20 psig - Answers c) 15 psig The primary water source for a recovery unit condensing coil is: _________. a) chilled water b) condenser water c) local municipal water supply d) de-ionized water - Answers c) local municipal water supply Which of the following repairs that would ALWAYS be considered "major" under EPA's regulations? a) replacement of an evaporator coil b) replacement of a filter-drier c) replacement of a switch d) replacement of a purge unit - Answers a) replacement of an evaporator coil According to the EPA, there is approximately ________ of refrigerant vapor left in an average 350 ton R-11 chiller at 0 psig pressure once all the R-11 liquid has been removed. a) None. b) 10 pounds. c) 20 pounds. d) 100 pounds. - Answers d) 100 pounds. A centrifugal chiller's rupture disk is connected to the chiller's: ________. a) condenser b) evaporator c) liquid line d) economizer - Answers b) evaporator When charging a chiller, refrigerant vapor is introduced into the system before charging with liquid. That is because: ___________. a) vapor charging increases pressure slowly, preventing failure of the rupture disc b) vapor charging is faster than liquid charging c) liquid charging is more difficult to control than vapor charging d) liquid charged into a deep vacuum will cause the refrigerant to boil and lower temperatures enough to freeze the water in the tubes - Answers d) liquid charged into a deep vacuum will cause the refrigerant to boil and lower temperatures enough to freeze the water in the tubes To determine how much vapor to charge into an evacuated chiller, you should charge with vapor until: __________. a) the system pressure corresponds to a refrigerant saturation temperature of 36 degrees F b) the recovery unit liquid level drops c) you have charged with vapor for 15 minutes d) the recovery unit pressure drops - Answers a) the system pressure corresponds to a refrigerant saturation temperature of 36 degrees F When there is excessive moisture collecting in the purge unit of a low pressure refrigeration system, this indicates that: _________.