Intermodal Dry Cargo CNTR/CSC
Reinspection (Cert), INTERMODAL DRY
CARGO CNTR/CSC REINSPEC EXAM
What is the primary reference used by inspectors to conduct CSC container
inspections? - answer-✔MIL-STD-3037
Which of the following containers allows for easier loading and unloading of large
bulky stock, such as bombs? - answer-✔Side-Opening
Which container component is highlighted? - answer-✔Threshold Plate
Which container component is highlighted? - answer-✔Top End Rail
Which container component is highlighted? - answer-✔Forklift Pockets
Which container component is highlighted? - answer-✔Gooseneck tunnel
What must be displayed on both ends, both sides, and the top of a container? -
answer-✔ISO Identification Markings
When inspecting containers, what tool would you use to inspect a container's
alignment? - answer-✔Measuring Tape
When inspecting containers, what tool is used to determine weld serviceability and
the severity of corrosion? - answer-✔Welder's Hammer
, When inspecting containers, what tool is used to move containers by lifting them at
the corner fittings? - answer-✔Container handler
Where do you find the container inspection checklist for a mobile facility? -
answer-✔MIL-STD-3037, Appendix A
Which statement is true? - answer-✔MIL-STD-3037 has separate paragraphs that
document IMDG and non-IMDG criteria.
What is the maximum allowable depth of a door header dent? Refer to MIL-STD-
3037, Section 4 as required. - answer-✔¾" for IMDG, 1-⅜" for general cargo
Select the appropriate defect classification for the following container defect: Dent
3/16" deep on the road side panel.
Refer to MIL-STD-3037, Section 4 as required. - answer-✔Minor
Refer to DA Form 2404 below. What is the appropriate entry for Item #5 in this
example? - answer-✔Unserviceable for IMDG and Non-IDMG
According to the DD Form 2282 decal shown below, when was this container last
inspected? - answer-✔May 2018
You inspected a container in April 2020. When is that container due for
reinspection? - answer-✔April 2022
Reinspection (Cert), INTERMODAL DRY
CARGO CNTR/CSC REINSPEC EXAM
What is the primary reference used by inspectors to conduct CSC container
inspections? - answer-✔MIL-STD-3037
Which of the following containers allows for easier loading and unloading of large
bulky stock, such as bombs? - answer-✔Side-Opening
Which container component is highlighted? - answer-✔Threshold Plate
Which container component is highlighted? - answer-✔Top End Rail
Which container component is highlighted? - answer-✔Forklift Pockets
Which container component is highlighted? - answer-✔Gooseneck tunnel
What must be displayed on both ends, both sides, and the top of a container? -
answer-✔ISO Identification Markings
When inspecting containers, what tool would you use to inspect a container's
alignment? - answer-✔Measuring Tape
When inspecting containers, what tool is used to determine weld serviceability and
the severity of corrosion? - answer-✔Welder's Hammer
, When inspecting containers, what tool is used to move containers by lifting them at
the corner fittings? - answer-✔Container handler
Where do you find the container inspection checklist for a mobile facility? -
answer-✔MIL-STD-3037, Appendix A
Which statement is true? - answer-✔MIL-STD-3037 has separate paragraphs that
document IMDG and non-IMDG criteria.
What is the maximum allowable depth of a door header dent? Refer to MIL-STD-
3037, Section 4 as required. - answer-✔¾" for IMDG, 1-⅜" for general cargo
Select the appropriate defect classification for the following container defect: Dent
3/16" deep on the road side panel.
Refer to MIL-STD-3037, Section 4 as required. - answer-✔Minor
Refer to DA Form 2404 below. What is the appropriate entry for Item #5 in this
example? - answer-✔Unserviceable for IMDG and Non-IDMG
According to the DD Form 2282 decal shown below, when was this container last
inspected? - answer-✔May 2018
You inspected a container in April 2020. When is that container due for
reinspection? - answer-✔April 2022
