EXAM STUDY MATERIALS 8/7/2024 11:29 AM
CCNA Introduction to Networks Chapter 6
Exam Questions With Correct Answers
Which router bootup sequence is correct? - answer✔✔1 - perform the POST and load the
bootstrap program
2 - locate and load the Cisco IOS software
3 - locate and load the startup configuration file or enter setup mode
Refer to curriculum topic: 6.3.2
When a router is powered on, it undergoes a POST to verify that the hardware is functional, after
which it proceeds by locating and loading the Cisco IOS software and then loading the startup
configuration file if one is present.
During troubleshooting procedures, from which location will most Cisco routers load a limited
IOS? - answer✔✔ROM
Refer to curriculum topic: 6.3.1
ROM is used to store bootup instructions, basic diagnostic software, and a copy of a limited IOS.
NVRAM stores the startup configuration file. RAM provides temporary storage of the running
configuration file. Flash is used to store the full Cisco IOS on a device.
Here is a link to the PT ActivityView in a new window.
Open the PT activity. Perform the tasks in the activity instructions and then answer the question.
Which interfaces in each router are active and operational? - answer✔✔R1: G0/0 and S0/0/0
R2: G0/1 and S0/0/0
R1>enable
R1# show ip int brief
, EXAM STUDY MATERIALS 8/7/2024 11:29 AM
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 192.168.20.1 YES manual up up
GigabitEthernet0/1 192.168.30.1 YES manual administratively down down
Serial0/0/0 209.165.200.225 YES manual up up
Serial0/0/1 unassigned YES unset administratively down down
Vlan1 unassigned YES unset administratively down down
R2>enable
R2#show ip int brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 10.1.2.1 YES manual administratively down down
GigabitEthernet0/1 10.1.3.1 YES manual up up
Serial0/0/0 209.165.200.226 YES manual up up
Serial0/0/1 unassigned YES unset administratively down down
Vlan1 unassigned YES unset administratively down down
Refer to curriculum topic: 6.4.2
The command to use for this activity is show ip interface brief in each router. The active and
operational interfaces are represented by the value "up" in the "Status" and "Protocol" columns.
The interfaces in R1 with these characteristics are G0/0 and S0/0/0. In R2 they are G0/1 and
S0/0/0.
Which two files are loaded into RAM by the router when it boots? (Choose two.) -
answer✔✔startup configuration
IOS image
Refer to curriculum topic: 6.3.2
CCNA Introduction to Networks Chapter 6
Exam Questions With Correct Answers
Which router bootup sequence is correct? - answer✔✔1 - perform the POST and load the
bootstrap program
2 - locate and load the Cisco IOS software
3 - locate and load the startup configuration file or enter setup mode
Refer to curriculum topic: 6.3.2
When a router is powered on, it undergoes a POST to verify that the hardware is functional, after
which it proceeds by locating and loading the Cisco IOS software and then loading the startup
configuration file if one is present.
During troubleshooting procedures, from which location will most Cisco routers load a limited
IOS? - answer✔✔ROM
Refer to curriculum topic: 6.3.1
ROM is used to store bootup instructions, basic diagnostic software, and a copy of a limited IOS.
NVRAM stores the startup configuration file. RAM provides temporary storage of the running
configuration file. Flash is used to store the full Cisco IOS on a device.
Here is a link to the PT ActivityView in a new window.
Open the PT activity. Perform the tasks in the activity instructions and then answer the question.
Which interfaces in each router are active and operational? - answer✔✔R1: G0/0 and S0/0/0
R2: G0/1 and S0/0/0
R1>enable
R1# show ip int brief
, EXAM STUDY MATERIALS 8/7/2024 11:29 AM
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 192.168.20.1 YES manual up up
GigabitEthernet0/1 192.168.30.1 YES manual administratively down down
Serial0/0/0 209.165.200.225 YES manual up up
Serial0/0/1 unassigned YES unset administratively down down
Vlan1 unassigned YES unset administratively down down
R2>enable
R2#show ip int brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 10.1.2.1 YES manual administratively down down
GigabitEthernet0/1 10.1.3.1 YES manual up up
Serial0/0/0 209.165.200.226 YES manual up up
Serial0/0/1 unassigned YES unset administratively down down
Vlan1 unassigned YES unset administratively down down
Refer to curriculum topic: 6.4.2
The command to use for this activity is show ip interface brief in each router. The active and
operational interfaces are represented by the value "up" in the "Status" and "Protocol" columns.
The interfaces in R1 with these characteristics are G0/0 and S0/0/0. In R2 they are G0/1 and
S0/0/0.
Which two files are loaded into RAM by the router when it boots? (Choose two.) -
answer✔✔startup configuration
IOS image
Refer to curriculum topic: 6.3.2
