Pipefitter Test Part II Questions with Correct Answers

Pipefitter Test Part II Questions with Correct Answers The two types of scaffolds used by pipefitters is the tubular buck and: - Correct Answer pole What is the take-out for a 10" long radius 45 degree elbow? - Correct Answer 6 & 1/4" According to OSHA, while working in an excavation, what is the MAXIMUM distance that a worker can be from a ladder? - Correct Answer 25 ft Which of the following types of copper tubing has the thickest wall? - Correct Answer K Arm extended, hand closed, thumb pointing upward signals to the crane operator to: - Correct Answer boom up What determines the thickness of a test blind? - Correct Answer The design temperature of the system If the sling is NOT placed in the center of the hook, the working load limit will: - Correct Answer be increased What is the product of 7.60 X 0.12? - Correct Answer 0.912 What do vents accomplish when installed in vessels? - Correct Answer Release pressure when filling Which of the following is a classification of cast iron pipe? - Correct Answer XH An obtuse triangle is defined as: - Correct Answer more than 90 degrees Information referring to design requirements and materials for pipe, flanges, valves, and related items to be used is found in: - Correct Answer Specifications What would be used to protect male threads on a carbon steel pipe? - Correct Answer Plastic cap Drawings that have been revised to show significant changes made during the construction process are called: - Correct Answer As-built The high pressure gauge on an oxyfuel regulator indicates the pressure: - Correct Answer in the tank What is the reference angle if the hypotenuse of a right triangle is 36" and its adjacent side is 14"? - Correct Answer 79 degrees Trenches MUST be designed, excavated, and shored according to: - Correct Answer OSHA standards What does the abbreviation TBE on a drawing stand for? - Correct Answer Threaded Both Ends Who needs to inspect an excavation prior to the start of work each day? - Correct Answer Competent person A preventative maintenance schedule calls for a specific valve to be lubricated. Grease is generally applied to which part of the valve? - Correct Answer Seat All of the following drawing dimensions are used to determine the overall length of run of a pipe, EXCEPT: - Correct Answer Pipe diameter A vertical pipe filled with 10' of water has a head pressure of: - Correct Answer 4.33 psi Threaded bushings are MOST commonly used when: - Correct Answer attaching threaded pipe to instrument tubing The PREFERRED method for cutting a pipe for socket welding, is the: - Correct Answer band saw process What is the takeoff for a 3" 45 degree butt-weld fitting? - Correct Answer 2" How many feet apart must oxygen and fuel gas cylinders be stored unless there is a 5' high 30 minute burn rated wall between **** - Correct Answer 5 Expansion joints allow: - Correct Answer for linear expansion and contraction of pipelines In calculating a 45 degree offset, what is the set multiplied by to determine the travel? - Correct Answer 1.414 What is the standard pipe thread that is used in the United States? - Correct Answer NPT The rigger MUST carefully inspect the chain hoist: - Correct Answer before each use How much would a 40'-6" length of 12" diameter standard weight pipe weigh? - Correct Answer 2009 lbs What is the highest safe standing step or level from the top of a straight or an extension ladder? - Correct Answer 4th Stainless steel material is generally used for pipe requiring protection from: - Correct Answer corrosion What is the length of the travel to the nearest 1/16" of a rolling offset that has a run of 18", a roll of 12", and a height of 10"? - Correct Answer 23 & 13/16 Convert 1/4 to its decimal equivalent: - Correct Answer 0.25 A 6-inch, 90-degree "saddle on" for a 12-inch header is to be fabricated. How far apart will the ordinate lines for this layout be? - Correct Answer 2 & 7/16 inches What would a piece of plate that is 28" wide by 48" long by 2" thick and is made of a material that weighs 490 lbs per cubic *** - Correct Answer 762.2 pounds Two-hole pins are used to: - Correct Answer orientate a flange on the end of a pipe Performance, reliability, and quality of components are assured by use of: - Correct Answer a qualified journeyman What is the highest safe standing step or level from the top of a step ladder (A-frame)? - Correct Answer Third What is the center line elevation of line number 4"2002? - Correct Answer 117 ft 8 & 1/4 inches