J-STD-001 Exam with correct Answers
Who is responsible for identifying the assembly class? - Answer -User
What is a defect? - Answer -A condition that may affect the form, fit, or function of the
item in the end use environment
Hardware found to not conform to the requirements of the standard shall be classified
as defects and dispositioned for: - Answer -[D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: -
Answer -[D1D2D3]
A documented process control system shall be implemented for: - Answer -[N1N2D3]
The contract shall take precedence over this standard for: - Answer -[D1D2D3]
What is wire overlap? - Answer -When a wire is wrapped more than 360 and crosses
over itself
What is wire over wrap? - Answer -When a wire is wrapped more than 360 and remains
in contact with the terminal
Manufacturers shall perform 100% inspection unless sampling inspection is defined for:
- Answer -[N1D2D3]
Inspection of soldering and cleanliness shall be performed prior to conformal coasting,
staking, or encapsulation for: - Answer -[N1D2D3]
Illumination at the surface of work stations should be at least what? - Answer -1000 lux
What is the tolerance for magnification aids? - Answer -+- 15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: -
Answer -[D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: - Answer
-[N1D2D3]
Manufacturer shall establish an ESD control program for: - Answer -[D1D2D3]
, What is J-STD-002? - Answer -Solder-ability tests for Component leads, terminations,
lugs, wires, and terminals
What is J-STD-003? - Answer -Solder ability tests for printed boards
What is J-STD-004? - Answer -Requirements for Soldering Fluxes
What is J-STD-005? - Answer -Requirements for Soldering Paste
What is J-STD-006? - Answer -Requirements for electronic grade solder alloys, fluxed
and non-fluxed solid solders
Manufacturers shall have a Pb-free control plan for: - Answer -[N1N2D3]
Items exposed to uncured silicone material shall not be used for processing other
material for: - Answer -[D1D2D3]
Solder alloys shall be in accordance with J-STD-006 or equivalent for: - Answer -
[D1D2D3]
Solder paste shall be in accordance with J-STD-005 or equivalent for: - Answer -
[D1D2D3]
Pb-free processing shall be in accordance with a documental procedure for: - Answer -
[N1D2D3]
SnPb solder alloys other than ... shall be in compliance for: - Answer -[N1D2D3]
Dross shall be removed from the solder surface without contacting tinned or soldered
items for: - Answer -[N1D2D3]
Type H or M fluxes shall not be used for tinning of stranded wires for: - Answer -
[D1D2D3]
Flux shall be in accordance with J-STD-004 or equivalent for: - Answer -[D1D2D3]
Adhesives shall not be detrimental and shall be cured for: - Answer -[D1D2D3]
Component coating meniscus shall not be trimmed for: - Answer -[N1D2D3]
A tool used to cut leads shall not impart shock that damages something for: - Answer -
[D1D2D3]
Loss of metallization as a result of processing shall not expose ceramic on terminal end
face ... for: - Answer -[D1D2D3]
Who is responsible for identifying the assembly class? - Answer -User
What is a defect? - Answer -A condition that may affect the form, fit, or function of the
item in the end use environment
Hardware found to not conform to the requirements of the standard shall be classified
as defects and dispositioned for: - Answer -[D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: -
Answer -[D1D2D3]
A documented process control system shall be implemented for: - Answer -[N1N2D3]
The contract shall take precedence over this standard for: - Answer -[D1D2D3]
What is wire overlap? - Answer -When a wire is wrapped more than 360 and crosses
over itself
What is wire over wrap? - Answer -When a wire is wrapped more than 360 and remains
in contact with the terminal
Manufacturers shall perform 100% inspection unless sampling inspection is defined for:
- Answer -[N1D2D3]
Inspection of soldering and cleanliness shall be performed prior to conformal coasting,
staking, or encapsulation for: - Answer -[N1D2D3]
Illumination at the surface of work stations should be at least what? - Answer -1000 lux
What is the tolerance for magnification aids? - Answer -+- 15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: -
Answer -[D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: - Answer
-[N1D2D3]
Manufacturer shall establish an ESD control program for: - Answer -[D1D2D3]
, What is J-STD-002? - Answer -Solder-ability tests for Component leads, terminations,
lugs, wires, and terminals
What is J-STD-003? - Answer -Solder ability tests for printed boards
What is J-STD-004? - Answer -Requirements for Soldering Fluxes
What is J-STD-005? - Answer -Requirements for Soldering Paste
What is J-STD-006? - Answer -Requirements for electronic grade solder alloys, fluxed
and non-fluxed solid solders
Manufacturers shall have a Pb-free control plan for: - Answer -[N1N2D3]
Items exposed to uncured silicone material shall not be used for processing other
material for: - Answer -[D1D2D3]
Solder alloys shall be in accordance with J-STD-006 or equivalent for: - Answer -
[D1D2D3]
Solder paste shall be in accordance with J-STD-005 or equivalent for: - Answer -
[D1D2D3]
Pb-free processing shall be in accordance with a documental procedure for: - Answer -
[N1D2D3]
SnPb solder alloys other than ... shall be in compliance for: - Answer -[N1D2D3]
Dross shall be removed from the solder surface without contacting tinned or soldered
items for: - Answer -[N1D2D3]
Type H or M fluxes shall not be used for tinning of stranded wires for: - Answer -
[D1D2D3]
Flux shall be in accordance with J-STD-004 or equivalent for: - Answer -[D1D2D3]
Adhesives shall not be detrimental and shall be cured for: - Answer -[D1D2D3]
Component coating meniscus shall not be trimmed for: - Answer -[N1D2D3]
A tool used to cut leads shall not impart shock that damages something for: - Answer -
[D1D2D3]
Loss of metallization as a result of processing shall not expose ceramic on terminal end
face ... for: - Answer -[D1D2D3]
