CWB 47.1 question n answers graded A+ 2023/2024

CWB 47.1CSA Standard W47.1 provides the requirements that must be met and adhered to by a company seeking certification. True or False? - correct answer True Certification can be considered as an approval of the products fabricated by a certificated company? True or false?! - correct answer False What does "class" refer to? A) "T", "S", "FW", "ASW" or "WT" designation of welding personnel. B) Electrode groups C) a category of welder qualification, e.g., F, H,V or O welding position D) Fillet and groove we'd combined test plate assemblies - correct answer C What does classification refer to? A) "T", "S", "FW", "ASW" or "WT" designation of welding personnel. B) Electrode groups C) a category of welder qualification, e.g., F, H,V or O welding position D) Fillet and groove we'd combined test plate assemblies - correct answer A What organization administer CSA Standard W47.1 A) there is no administrator B) Canadian standards association C) Canadian welding bureau - correct answer C The Canadian welding bureau can withdraw a company's certification if the company is NOT following the requirements of CSA standard W47.1 True or false ? - correct answer True How many divisions of certification are specified in CSA Standard W47.1 ? A) one B) two C) three D) four - correct answer C Is a company certified in division 1 required to employ a full time or retain a part time welding engineer? A) retain a part time welding engineer B) employ a full time welding engineer C) no engineer is required D) employ a full time welding inspector only - correct answer B Is a company certified in division 3 required to employ a full time or retain a part time welding engineer? A) Employ a full time welding engineer B) Retain a part time welding engineer C) retain a part time welding engineer responsible to the company only for welding procedures and practice D) No welding engineer is required - correct answer D CSA Standard W47.1 requires each designated plant, shop or section to meet the requirements of certification within this standard with respect to welders, welding procedures specification, welding procedure data sheets, welding supervisor and welding engineer, where applicable True or false? - correct answer True A company doing only erection work involving welding must have a pony in order to be certified to CSA standard W47.1 True or false? - correct answer False When must the company inform the Canadian bureau of any loss or change in welding engineering or supervisory personnel? A) immediately B) after 3 months C) after 6 months D) the doesn't have to inform as long as the personnel is replaced after a year - correct answer A The company shall designate an individual who, irrespective of each other responsibilities, shall have defined authority and responsibility for ensuring that the requirements of CSA Standard W47.1 are implemented and maintained True or false? - correct answer True What are the duties of the welding engineer? A) Provide engineering support to the company as required. B) Development of new welding procedures C) Periodic reviews of the company's welding practices D) preparation of WPSs and WPDSs E) all of the above - correct answer E A welding supervisor with two years of fabrication experience is acceptable for division 1 company? True or false? - correct answer False Each supervisor shall have knowledge of? A) weld faults B) Quality control C) Estimating D) both a & c pertaining to directly related to their work. - correct answer D Each supervisor shall be able to read drawings and to properly interpret welding symbols. True or false? - correct answer True Who is responsible for ensuring that the companies personnel involved in welding are qualified and working with approved welding procedures in the shop or in the field? A) the welders themselves B) no one is responsible because the welders have shown their performance abilities when they are qualified in accordance with the standard C) the welding supervisor D) the welding engineer must ensure a satisfactory performance of welders in production welding through continuous guidance and instruction - correct answer C If there is a reason to doubt the welders ability, his/her qualification is suspended immediately and shall be required to pass a check test in the position and class held True of false? - correct answer True What types of identification cards are issued to welders by the Canadian welding bureau? A) transferable card when qualification is based on standard test assemblies B) transferable card when qualification is based on non standard test assemblies C) nontransferable card when qualification is based on non standard test assemblies D) a letter in lieu of an identification card E) a, c, & d - correct answer E Who owns the welder cards that are issued by the Canadian welding bureau? A) the company B) the welder C) the Canadian welding bureau D) the welding supervisor - correct answer C Who is responsible for ensuring that welders identification cards or copies thereof can be produced as proof that a welder has valid qualification? A) the welder