BECC MOD 1 TEST 2023
What ARE 3 considerations when dealing with electrical burns? - ANSWER
Electrical current may burn a large area just below the surface
Perform CPR if needed
Treatment is the same as for a thermal burn
(True/False) Section 300 of the PQS book list infrequent task and abnormal
conditions. - ANSWER TRUE
The overall purpose of PQS is to ...... - ANSWER provide a means to qualify ships
personnel.
(True/False) PQS provides an effective way to monitor an individual's qualification
progress. - ANSWER TRUE
When can your Final Qualification Page be signed?. - ANSWER After all line
items have been completed and signed
Vocabulary used in each qualification can be found in the ....... Section of the PQS
book. - ANSWER FUNDAMENTALS
Progress and completed qualifications of each person in the division are displayed
on/in the ....... - ANSWER PROGRESS CHART
Who is the final qualification authority? - ANSWER COMMANDING OFFICER
A five inch outside micrometer will measure objects that are ....... inches thick. -
ANSWER 4-5IN
A Dial indicator may be used to....... - ANSWER ALIGN MACHINERY
It is NOT safe to operate electrical power tools in areas where ....... is/are present. -
ANSWER FLAMMABLE GASES
Electrical power tools must be inspected prior to issue by a qualified ....... -
ANSWER ELECTRICIAN
A torque wrench is used to measure the tightness of ... - ANSWER FASTENERS
, Torque wrenches are considered ....... equipment - ANSWER PRECISION
If a maintenance procedure does not specify a torque sequence, utilize the
recommended sequence found in ....... - ANSWER NTM CHAPER 075
Which document contains maintenance requirements pertaining to all equipment
in a command? - ANSWER PMS MASTER FILE
16. Which portion of the PMS Master File provides the work center supervisor a
ready reference of planned maintenance requirements.? - ANSWER WORK
CENTER PMS MANUAL
If a planned maintenance action cannot be completed in accordance with the
steps listed on the MRC, the maintenance man should ....... - ANSWER STOP AND
REPORT TO THE WCS
What is used to notify personnel that death or injury may result if the operating
procedures and practices are NOT correctly followed? - ANSWER Warnings
Which of the following serves as the "Table of Contents" for the Work Center PMS
manual? - ANSWER LIST OF EFFECTIVE PAGES (LOEP)
The SYSCOM Control Number assigned for each maintenance requirement listed
in a MIP must match the number on the corresponding - ANSWER MRC
(maintenance requirement card)
Materials needed to perform the required maintenance are found on the -
ANSWER FRONT OF THE MRC
The responsibility to replace a missing MRC belongs to the ....... - ANSWER
WORK CENTER SUPERVISOR
Who assists the Department Head in managing maintenance at the division level?
- ANSWER DIVISION OFFICER
Who has the responsibility to maintain the list of effective pages? - ANSWER
WORK CENTER SUPERVISOR
Which schedule is NOT used in the 3M system? - ANSWER DAILY
Which of the following periodicity code is used when a maintenance requirement
is performed monthly? - ANSWER M
What ARE 3 considerations when dealing with electrical burns? - ANSWER
Electrical current may burn a large area just below the surface
Perform CPR if needed
Treatment is the same as for a thermal burn
(True/False) Section 300 of the PQS book list infrequent task and abnormal
conditions. - ANSWER TRUE
The overall purpose of PQS is to ...... - ANSWER provide a means to qualify ships
personnel.
(True/False) PQS provides an effective way to monitor an individual's qualification
progress. - ANSWER TRUE
When can your Final Qualification Page be signed?. - ANSWER After all line
items have been completed and signed
Vocabulary used in each qualification can be found in the ....... Section of the PQS
book. - ANSWER FUNDAMENTALS
Progress and completed qualifications of each person in the division are displayed
on/in the ....... - ANSWER PROGRESS CHART
Who is the final qualification authority? - ANSWER COMMANDING OFFICER
A five inch outside micrometer will measure objects that are ....... inches thick. -
ANSWER 4-5IN
A Dial indicator may be used to....... - ANSWER ALIGN MACHINERY
It is NOT safe to operate electrical power tools in areas where ....... is/are present. -
ANSWER FLAMMABLE GASES
Electrical power tools must be inspected prior to issue by a qualified ....... -
ANSWER ELECTRICIAN
A torque wrench is used to measure the tightness of ... - ANSWER FASTENERS
, Torque wrenches are considered ....... equipment - ANSWER PRECISION
If a maintenance procedure does not specify a torque sequence, utilize the
recommended sequence found in ....... - ANSWER NTM CHAPER 075
Which document contains maintenance requirements pertaining to all equipment
in a command? - ANSWER PMS MASTER FILE
16. Which portion of the PMS Master File provides the work center supervisor a
ready reference of planned maintenance requirements.? - ANSWER WORK
CENTER PMS MANUAL
If a planned maintenance action cannot be completed in accordance with the
steps listed on the MRC, the maintenance man should ....... - ANSWER STOP AND
REPORT TO THE WCS
What is used to notify personnel that death or injury may result if the operating
procedures and practices are NOT correctly followed? - ANSWER Warnings
Which of the following serves as the "Table of Contents" for the Work Center PMS
manual? - ANSWER LIST OF EFFECTIVE PAGES (LOEP)
The SYSCOM Control Number assigned for each maintenance requirement listed
in a MIP must match the number on the corresponding - ANSWER MRC
(maintenance requirement card)
Materials needed to perform the required maintenance are found on the -
ANSWER FRONT OF THE MRC
The responsibility to replace a missing MRC belongs to the ....... - ANSWER
WORK CENTER SUPERVISOR
Who assists the Department Head in managing maintenance at the division level?
- ANSWER DIVISION OFFICER
Who has the responsibility to maintain the list of effective pages? - ANSWER
WORK CENTER SUPERVISOR
Which schedule is NOT used in the 3M system? - ANSWER DAILY
Which of the following periodicity code is used when a maintenance requirement
is performed monthly? - ANSWER M
