FEEL THE HEAT GIZMOS ANSWER KEY WITH COMPLETE SOLUTION Course PHY 111 Institution Anne Arundel Community College Feel the Heat Gizmos Answer Key with complete solution

2019 Feel the Heat Answer Key Vocabulary : calorimeter , conductor, controlled experiment, dissolve, endothermic, exothermic, insulator , solute, solution, solvent, surroundings, system Prior Knowledge Questions (Do these BEFORE using the Gizmo.) [Note: The purpose of these questions is to activate prior knowledge and get students thinking. Students are not expected t o know the answers to the Prior Knowledge Questions.] Eduardo hurts his knee during a basketball game. The trainer applies a cold pack, which gets cold after being squeezed. The next day, Eduardo’s friend Beth is going sledding. Beth buys some hand warmers and puts them into her gloves. All morning, her hands stay toasty warm. 1. How do you think these devices work? Answers will vary. [Cold packs typically work by dissolving a salt such as ammonium nitrate into water. Commercial hot packs work by crystalizing sodium acetate or by oxidizing iron.] 2. Where do you think the “cold” and the heat comes from? Answers will vary. Gizmo Warm -up As you saw with the instant cold pack and the hand warmers , some reactions absorb energy while others release it. In the Feel the Heat Gizmo, you will explore these energy changes while making your own hot and cold packs. To begin, select the TEST POWDERS tab. D rag a bottle of NaC 2H3O2 (sodium acetate) f rom the shelf. Using the sliders, decide how much water and powder to add. Note the beginning temperature, a nd then press Play () to see what happens. 1. Did the temperature go up or down? Up 2. Experiment with different powders until you find one that produces the opposite effect . What powder did you use? NH 4NO 3, KCl , and NaCl will produce a temperature dec rease . When a powder dissolves in water a solution is formed. The powder is the solute and the water is the solvent. Oftentimes energy changes accompany the formation of a solution. When added to water, some powders cause the resulting solution to get hot, while others make it cold. Some powders don’t produce a temperature change at all. When energy changes do occur, they can be put to good use. This study source was downloaded by 100000846041611 from CourseHero.com on 12-28-2022 00:02:46 GMT -06:00
https://www.coursehero.com/collection/71553815/FeeltheHeatSE-Keypdf/
FEEL THE HEAT 2019 Activity A: Molecular view Get the Gizmo ready :  Click Reset ().  Drag a bottle of NaC 2H3O2 from the shelf. Introduction: The reactions in this activity are performed within a calorimeter , an insulated device that keeps heat from escaping, enabl ing you to accurately record temperature changes . Question: Why does the temperature change when a powder is dissolved in water ? 1. Observe : Turn on Show molecular view , and n otice the water molecules. Set the Water volume to 100 mL and the Powder mass to 20 g , and then c lick Play. Click Pause () after adding the powder . You should now see show some sodium acetate in the water. A. What color represents the bonds between the particles of NaC 2H3O2? Orange B. Click Play. Watch the animation a few times. What happens to the NaC 2H3O2 bonds? They are broken. C. What happens to the bonds between water molecules? They are broken. D. What color are the new bonds that form between the solute and solvent? Blue 2. Investigate : In the animation , the purple arrows represent energy that is being absorbed from the water , while the orange arrows show energy that is being released into the solution . A. Replay the animation, carefully noting the purple arrows. What does this absorbed energy do? The absorbed energy b reaks apart bonds between the solute particles. B. Now replay the animation but focus on the orange arrows. What occur s every time an orange arrow is released? New bonds are formed between solute and solvent. C. Fill in the blanks: When bonds are broken, energy is absorbed . When new bonds form, energy is released . D. Based on the arrow sizes, do you think more energy is absorbed in breaking bonds, or is more energy released when new bonds form? More energy is released . E. Which bonds do you think are stronger, the bonds that are broken or the bonds that are formed? Explain your reasoning. The bonds that are formed are stronger. Since m ore energy is released as a result of bond formation than is absorbed to break bonds, the bonds formed must be stronger. (Activity A continued on next page) This study source was downloaded by 100000846041611 from CourseHero.com on 12-28-2022 00:02:46 GMT -06:00
https://www.coursehero.com/collection/71553815/FeeltheHeatSE-Keypdf/