Connecticut (CT) Hoisting Equipment Operator
Exam
Which Connecticut agency regulates hoisting equipment operators?
A) Connecticut Department of Labor
B) Connecticut Department of Transportation
C) Connecticut Department of Public Safety
D) Connecticut Department of Consumer Protection
ANSWER: D) Connecticut Department of Consumer Protection
EXPLANATION: The Connecticut Department of Consumer Protection, Occupational and
Professional Licensing Division, regulates hoisting equipment operators under Connecticut
General Statutes Chapter 394.
What is the minimum age requirement for a hoisting equipment operator license in
Connecticut?
A) 16 years
B) 18 years
C) 21 years
D) 25 years
ANSWER: B) 18 years
EXPLANATION: Applicants must be at least 18 years old to obtain a hoisting equipment
operator license in Connecticut.
Which certification is required for crane operators in Connecticut?
A) NCCCO certification
,B) OSHA 10-hour card
C) Both A and B
D) Neither A nor B
ANSWER: A) NCCCO certification
EXPLANATION: Connecticut requires NCCCO (National Commission for the Certification of
Crane Operators) certification for crane operators.
What is the maximum wind speed for operating most cranes?
A) 20 mph
B) 30 mph
C) 35 mph
D) 40 mph
ANSWER: C) 35 mph
EXPLANATION: Most crane operations must cease when wind speeds exceed 35 mph,
unless manufacturer specifications allow higher limits.
Which type of crane has a rotating superstructure?
A) Tower crane
B) Mobile crane
C) Overhead crane
D) All of the above
ANSWER: D) All of the above
EXPLANATION: All these crane types typically have rotating superstructures.
,What is the purpose of an anti-two-block device?
A) Prevent overloading
B) Prevent boom collapse
C) Prevent two-blocking
D) Prevent tipping
ANSWER: C) Prevent two-blocking
EXPLANATION: Anti-two-block devices prevent the load block from contacting the boom
tip, which can cause catastrophic failure.
Which document must be completed before crane setup?
A) Pre-lift meeting report
B) Lift plan
C) Site survey
D) All of the above
ANSWER: D) All of the above
EXPLANATION: All these documents are part of proper lift planning and preparation.
What is the minimum clearance from power lines for cranes?
A) 10 feet
B) 20 feet
C) 30 feet
D) 50 feet
ANSWER: B) 20 feet
, EXPLANATION: OSHA requires minimum 20-foot clearance from power lines up to 350kV,
with greater distances for higher voltages.
Which factor is NOT part of lift capacity calculations?
A) Boom length
B) Operator experience
C) Radius
D) Counterweight
ANSWER: B) Operator experience
EXPLANATION: Capacity calculations consider boom length, radius, counterweight, and
other mechanical factors, not operator experience.
What is the purpose of outriggers?
A) Increase stability
B) Increase mobility
C) Reduce weight
D) All of the above
ANSWER: A) Increase stability
EXPLANATION: Outriggers extend the crane's base to increase stability during lifting
operations.
How often must hoisting equipment be inspected?
A) Daily
B) Monthly
C) Annually
Exam
Which Connecticut agency regulates hoisting equipment operators?
A) Connecticut Department of Labor
B) Connecticut Department of Transportation
C) Connecticut Department of Public Safety
D) Connecticut Department of Consumer Protection
ANSWER: D) Connecticut Department of Consumer Protection
EXPLANATION: The Connecticut Department of Consumer Protection, Occupational and
Professional Licensing Division, regulates hoisting equipment operators under Connecticut
General Statutes Chapter 394.
What is the minimum age requirement for a hoisting equipment operator license in
Connecticut?
A) 16 years
B) 18 years
C) 21 years
D) 25 years
ANSWER: B) 18 years
EXPLANATION: Applicants must be at least 18 years old to obtain a hoisting equipment
operator license in Connecticut.
Which certification is required for crane operators in Connecticut?
A) NCCCO certification
,B) OSHA 10-hour card
C) Both A and B
D) Neither A nor B
ANSWER: A) NCCCO certification
EXPLANATION: Connecticut requires NCCCO (National Commission for the Certification of
Crane Operators) certification for crane operators.
What is the maximum wind speed for operating most cranes?
A) 20 mph
B) 30 mph
C) 35 mph
D) 40 mph
ANSWER: C) 35 mph
EXPLANATION: Most crane operations must cease when wind speeds exceed 35 mph,
unless manufacturer specifications allow higher limits.
Which type of crane has a rotating superstructure?
A) Tower crane
B) Mobile crane
C) Overhead crane
D) All of the above
ANSWER: D) All of the above
EXPLANATION: All these crane types typically have rotating superstructures.
,What is the purpose of an anti-two-block device?
A) Prevent overloading
B) Prevent boom collapse
C) Prevent two-blocking
D) Prevent tipping
ANSWER: C) Prevent two-blocking
EXPLANATION: Anti-two-block devices prevent the load block from contacting the boom
tip, which can cause catastrophic failure.
Which document must be completed before crane setup?
A) Pre-lift meeting report
B) Lift plan
C) Site survey
D) All of the above
ANSWER: D) All of the above
EXPLANATION: All these documents are part of proper lift planning and preparation.
What is the minimum clearance from power lines for cranes?
A) 10 feet
B) 20 feet
C) 30 feet
D) 50 feet
ANSWER: B) 20 feet
, EXPLANATION: OSHA requires minimum 20-foot clearance from power lines up to 350kV,
with greater distances for higher voltages.
Which factor is NOT part of lift capacity calculations?
A) Boom length
B) Operator experience
C) Radius
D) Counterweight
ANSWER: B) Operator experience
EXPLANATION: Capacity calculations consider boom length, radius, counterweight, and
other mechanical factors, not operator experience.
What is the purpose of outriggers?
A) Increase stability
B) Increase mobility
C) Reduce weight
D) All of the above
ANSWER: A) Increase stability
EXPLANATION: Outriggers extend the crane's base to increase stability during lifting
operations.
How often must hoisting equipment be inspected?
A) Daily
B) Monthly
C) Annually
