MILLWRIGHT ALBERTA STUDY SHEET
RESOURCES 2026 VERIFIED SOLUTIONS
READY
◍ when is a whimis label not required? Answer: when a controlled
product is used immediately
◍ intentional difference between mating parts? Answer: allowance
◍ the amount of variation between parts Answer: tolerance
◍ gap or space between mating parts Answer: clearance
◍ what is used with an outside caliper to measure a shaft? Answer:
a steel rule
◍ vernier caliper smallest measurement? Answer: one thou if an
inch 0.001" or 0.20mm
◍ parallel misalignment + angular misalignment Answer:
combination misalignment
◍ how to measure a small hole? Answer: small hole gauge and
outside micrometer
, ◍ Reading a Vernier bevel protractor in what ? Answer: main scale
is degrees and vernier scale is minutes indicates every 5 minutes =
1/12 of a degree
◍ What has to be aligned during machine installation Answer:
Centerlines
◍ what's a datum line Answer: standard of comparison or point of
reference
◍ most important point prior to a layout is Answer: reference
line/datum line
◍ smallest dimension on a steel rule Answer: 1/64th
◍ accuracy of a vernier caliper Answer: 0.01mm or 0.001" (one
thou)
◍ What do you use to set the axis of the threading tool at a right
angle to the axis of the workpiece? Answer: thread centre gauge
(fishtail)
◍ sensitive tool that is used to measure the depth of small holes and
bores? Answer: depth micrometer (scale runs opposite to most
micrometers)
, ◍ smallest measurement on a vernier metric micrometer Answer:
0.001 mm
◍ Type of wrench used on a polished or smooth surface? Answer:
Strap Wrench
◍ Puller used for removing Bearing? Answer: Pressure Screw
Puller
◍ 4 types of Pullers? Answer: pressure screw puller
Hydraulic puller
Slide hammer puller
Bar-style puller
◍ What is a ball peen hammer used for? Answer: Riveting
◍ # teeth on a hacksaw for cutting a 1" aluminum shaft? Answer:
14 pitch blade
◍ a coarse pitch blade is best for Answer: soft material
◍ a fine pitch blade is best for Answer: hard material
◍ which file has the smoothest cut? Answer: Single cut file
RESOURCES 2026 VERIFIED SOLUTIONS
READY
◍ when is a whimis label not required? Answer: when a controlled
product is used immediately
◍ intentional difference between mating parts? Answer: allowance
◍ the amount of variation between parts Answer: tolerance
◍ gap or space between mating parts Answer: clearance
◍ what is used with an outside caliper to measure a shaft? Answer:
a steel rule
◍ vernier caliper smallest measurement? Answer: one thou if an
inch 0.001" or 0.20mm
◍ parallel misalignment + angular misalignment Answer:
combination misalignment
◍ how to measure a small hole? Answer: small hole gauge and
outside micrometer
, ◍ Reading a Vernier bevel protractor in what ? Answer: main scale
is degrees and vernier scale is minutes indicates every 5 minutes =
1/12 of a degree
◍ What has to be aligned during machine installation Answer:
Centerlines
◍ what's a datum line Answer: standard of comparison or point of
reference
◍ most important point prior to a layout is Answer: reference
line/datum line
◍ smallest dimension on a steel rule Answer: 1/64th
◍ accuracy of a vernier caliper Answer: 0.01mm or 0.001" (one
thou)
◍ What do you use to set the axis of the threading tool at a right
angle to the axis of the workpiece? Answer: thread centre gauge
(fishtail)
◍ sensitive tool that is used to measure the depth of small holes and
bores? Answer: depth micrometer (scale runs opposite to most
micrometers)
, ◍ smallest measurement on a vernier metric micrometer Answer:
0.001 mm
◍ Type of wrench used on a polished or smooth surface? Answer:
Strap Wrench
◍ Puller used for removing Bearing? Answer: Pressure Screw
Puller
◍ 4 types of Pullers? Answer: pressure screw puller
Hydraulic puller
Slide hammer puller
Bar-style puller
◍ What is a ball peen hammer used for? Answer: Riveting
◍ # teeth on a hacksaw for cutting a 1" aluminum shaft? Answer:
14 pitch blade
◍ a coarse pitch blade is best for Answer: soft material
◍ a fine pitch blade is best for Answer: hard material
◍ which file has the smoothest cut? Answer: Single cut file
