100 elevator final exam (Latest
Update) Questions and Verified Answers
100% Correct {Grade A}
What are the two most common causes of accidents to members of the general
public on elevators? -correct answer Trips and falls, and being struck by the doors
Before shortening a governor rope, what safety steps should be taken? -correct
answer LOTO and support tension sheave
You aren't sure if a particular hoistway is considered a permit-required confined
space. Where can you find more information? -correct answer OSHA 29 CFR 1926
code
You arrive at the machine room to replace a thrust bearing and find the lights are not
working. What should you do? -correct answer Do not start work until the lighting is
restored
After locking out and tagging out the electrical system, what safety step must be
taken before entering an escalator truss? -correct answer Install a mechanical lock
A mechanic is about to lubricate a governor tension sheave in a traction elevator pit.
Before beginning work, what must be done? -correct answer Lock out and tag out
An elevator constructor is asked to check on something in the pit. When must
barriers be installed? -correct answer When hoistway door will be open more than 5"
,100 elevator final exam (Latest
Update) Questions and Verified Answers
100% Correct {Grade A}
When is public safety an elevator constructors responsibility? -correct answer During
all work-related activities
When carrying a screwdriver in your pocket on a car top, what safety factors must be
considered? -correct answer It doesn't matter; you should never carry a screw driver
in your pocket
You are ordering wood planking to provide overhead protection for a temporary
working platform. At a minimum, how thick must the wood be? -correct answer 2"
Which organization' s code prohibits storing anything on top of the car? -correct
answer ASME
You are modernizing an elevator where the Public is present. What are the barricade
requirements? -correct answer Solid barricade at least 8' high, fully enclosing the
work area
Why did the elevator mechanic direct the apprentice not to run gasoline generator in
an enclosed parking garage? -correct answer The risk of exposure to Carbon
Monoxide fumes
, 100 elevator final exam (Latest
Update) Questions and Verified Answers
100% Correct {Grade A}
A mechanic is checking the condition of the belts on a hydraulic elevator. When is it
safe to check the tension? -correct answer After locking out and tagging out the
mainline
When using power tools in older buildings without ground led outlets, what
precaution must you take? -correct answer Verify a positive ground and use an
adapter plug with grounding wire
In the elevator industry, why are fiberglass ladders the most common type of ladders
used? -correct answer They are non-conductive
When would a mechanic be required to replace an escalator comb or comb plate? -
correct answer When teeth are broken
Along with spring buffers, limit switches, and cylinder head packing, what else would
be found in a conventional hydraulic elevator pit? -correct answer Drip collection pan
or oil return system
When lifting heavy objects, what is the best lifting technique to use? -correct answer
Back straight, legs bent
When performing any work in a traction elevator pit, which hazard is known as the
silent killer -correct answer Counterweight
Update) Questions and Verified Answers
100% Correct {Grade A}
What are the two most common causes of accidents to members of the general
public on elevators? -correct answer Trips and falls, and being struck by the doors
Before shortening a governor rope, what safety steps should be taken? -correct
answer LOTO and support tension sheave
You aren't sure if a particular hoistway is considered a permit-required confined
space. Where can you find more information? -correct answer OSHA 29 CFR 1926
code
You arrive at the machine room to replace a thrust bearing and find the lights are not
working. What should you do? -correct answer Do not start work until the lighting is
restored
After locking out and tagging out the electrical system, what safety step must be
taken before entering an escalator truss? -correct answer Install a mechanical lock
A mechanic is about to lubricate a governor tension sheave in a traction elevator pit.
Before beginning work, what must be done? -correct answer Lock out and tag out
An elevator constructor is asked to check on something in the pit. When must
barriers be installed? -correct answer When hoistway door will be open more than 5"
,100 elevator final exam (Latest
Update) Questions and Verified Answers
100% Correct {Grade A}
When is public safety an elevator constructors responsibility? -correct answer During
all work-related activities
When carrying a screwdriver in your pocket on a car top, what safety factors must be
considered? -correct answer It doesn't matter; you should never carry a screw driver
in your pocket
You are ordering wood planking to provide overhead protection for a temporary
working platform. At a minimum, how thick must the wood be? -correct answer 2"
Which organization' s code prohibits storing anything on top of the car? -correct
answer ASME
You are modernizing an elevator where the Public is present. What are the barricade
requirements? -correct answer Solid barricade at least 8' high, fully enclosing the
work area
Why did the elevator mechanic direct the apprentice not to run gasoline generator in
an enclosed parking garage? -correct answer The risk of exposure to Carbon
Monoxide fumes
, 100 elevator final exam (Latest
Update) Questions and Verified Answers
100% Correct {Grade A}
A mechanic is checking the condition of the belts on a hydraulic elevator. When is it
safe to check the tension? -correct answer After locking out and tagging out the
mainline
When using power tools in older buildings without ground led outlets, what
precaution must you take? -correct answer Verify a positive ground and use an
adapter plug with grounding wire
In the elevator industry, why are fiberglass ladders the most common type of ladders
used? -correct answer They are non-conductive
When would a mechanic be required to replace an escalator comb or comb plate? -
correct answer When teeth are broken
Along with spring buffers, limit switches, and cylinder head packing, what else would
be found in a conventional hydraulic elevator pit? -correct answer Drip collection pan
or oil return system
When lifting heavy objects, what is the best lifting technique to use? -correct answer
Back straight, legs bent
When performing any work in a traction elevator pit, which hazard is known as the
silent killer -correct answer Counterweight
