Please write clearly in block capitals.
Centre number Candidate number
Surname __________________________________________________________________________
Forename(s) __________________________________________________________________________
Candidate signature __________________________________________________________________________
I declare this is my own work.
A-level
DESIGN AND TECHNOLOGY:
PRODUCT DESIGN
Paper 1 Technical Principles
Monday 2 June 2025 Morning Time allowed: 2 hours 30 minutes
For Examiner’s Use
Materials Question Mark
For this paper you must have:
1
l normal writing and drawing instruments
l a scientific calculator.
2
3–4
Instructions 5
l Use black ink or black ball-point pen. Use pencil only for drawing. 6
l Fill in the boxes at the top of this page. 7
l Answer all questions. 8
l You must answer the questions in the spaces provided. Do not write outside 9
the box around each page or on blank pages.
10
l If you need extra space for your answer(s), use the lined pages at the end of
11–12
this book. Write the question number against your answer(s).
l Do all rough work in this book. Cross through any work you do not want 13
to be marked. 14
15
Information 16
l The marks for questions are shown in brackets. 17–18
l The maximum mark for this paper is 120. 19
20–21
22–23
24
TOTAL
(JUN257552101)
G/KL/Jun25/G4006/V6 7552/1
, 2
Do not write
outside the
Answer all questions in the spaces provided. box
0 1 . 1 _ Identify the specific material classification of nylon.
[1 mark]
____________________________________________________________________________________
____________________________________________________________________________________
0 1 . 2 _State two specific properties of nylon.
[2 marks]
Property 1_________________________________________________________________________
____
Property 2_________________________________________________________________________ 3
(02)
G/Jun25/7552/1
, 3
Do not write
outside the
box
0 2 _ Use the information in Figure 1 to calculate the length of the cutter path shown.
Figure 1
Cutter path
R40
120
°
Not drawn to scale.
All dimensions in mm
_ Show your working out.
[3 marks]
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
____
Length of cutter path ___________________________________ mm 3
Turn over for the next question
Turn over U
(03)
G/Jun25/7552/1
Centre number Candidate number
Surname __________________________________________________________________________
Forename(s) __________________________________________________________________________
Candidate signature __________________________________________________________________________
I declare this is my own work.
A-level
DESIGN AND TECHNOLOGY:
PRODUCT DESIGN
Paper 1 Technical Principles
Monday 2 June 2025 Morning Time allowed: 2 hours 30 minutes
For Examiner’s Use
Materials Question Mark
For this paper you must have:
1
l normal writing and drawing instruments
l a scientific calculator.
2
3–4
Instructions 5
l Use black ink or black ball-point pen. Use pencil only for drawing. 6
l Fill in the boxes at the top of this page. 7
l Answer all questions. 8
l You must answer the questions in the spaces provided. Do not write outside 9
the box around each page or on blank pages.
10
l If you need extra space for your answer(s), use the lined pages at the end of
11–12
this book. Write the question number against your answer(s).
l Do all rough work in this book. Cross through any work you do not want 13
to be marked. 14
15
Information 16
l The marks for questions are shown in brackets. 17–18
l The maximum mark for this paper is 120. 19
20–21
22–23
24
TOTAL
(JUN257552101)
G/KL/Jun25/G4006/V6 7552/1
, 2
Do not write
outside the
Answer all questions in the spaces provided. box
0 1 . 1 _ Identify the specific material classification of nylon.
[1 mark]
____________________________________________________________________________________
____________________________________________________________________________________
0 1 . 2 _State two specific properties of nylon.
[2 marks]
Property 1_________________________________________________________________________
____
Property 2_________________________________________________________________________ 3
(02)
G/Jun25/7552/1
, 3
Do not write
outside the
box
0 2 _ Use the information in Figure 1 to calculate the length of the cutter path shown.
Figure 1
Cutter path
R40
120
°
Not drawn to scale.
All dimensions in mm
_ Show your working out.
[3 marks]
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
�����������������������������������������������������������������������������������
____
Length of cutter path ___________________________________ mm 3
Turn over for the next question
Turn over U
(03)
G/Jun25/7552/1