MAE 1351 NEWEST EXAM 3 2026 WITH
MULTIPLE CHOICE QUESTIONS AND
DETAILED SOLVED SOLUTIONS
ALREADY GRADED A+ AND 100% PASS
GUARANTEE (BRAND NEW
EDITION!!!!!!)
circles are typically dimensioned as - THE CORRECT ANSWER-
diameters
arcs are dimensioned as - THE CORRECT ANSWER-radii
T/F you should give dimensions between holes vs dimensioning
the holes from the end of the part - THE CORRECT ANSWER-True
Baseline Dimensioning - THE CORRECT ANSWER-all of the
dimensions in a given direction originate from a base or datum
(frequently used for CNC machines)
Chain Dimensioning - THE CORRECT ANSWER-features are
dimensioned relative to one another (used when a part function
requires that features be related to one another)
T/F chain dimensioning is often preferred over baseline - THE
CORRECT ANSWER-False, Baseline dimensioning is prefrred
,Chain dimensioning usually yields the _______ accumulation
of tolerance between features,where the maximum distance
between features is... - THE CORRECT ANSWER-largest; equal to the
sum of the intermediate distances
dimension only to _______ or _______ lines - THE CORRECT
ANSWER-visible; solid
Dimension lines also should be at least _____ ___ from any
view, helping to avoid clutter. - THE CORRECT ANSWER-10 mm
When dimensions are placed outside other dimensions, there
should be at least ___ ___ between dimension lines - THE
CORRECT ANSWER-6 mm
When dimensioning a visible gap of at least ___ ___ should be
between extension lines and object geometry - THE CORRECT
ANSWER-1 mm
when dimensioning, extension lines should extend ___-___
___ past their corresponding dimension line - THE CORRECT
ANSWER-2-3 mm
Chamfersy are dimensioned by - THE CORRECT ANSWER-giving a
length from the end of the part and an angle or by specifying
two distances
, |___| represents what on a drawing? - THE CORRECT ANSWER-
counterbore
\/ represents what on a drawing? - THE CORRECT ANSWER-
countersink
a line with an arrow pointing down represents what on a
drawing? - THE CORRECT ANSWER-specifying depth
Unless otherwise specified, all geometric tolerances apply for... -
THE CORRECT ANSWER-full depth, length, and width of the feature
notes typically appear in the _____________________
corner of a drawing and apply to the whole drawing - THE CORRECT
ANSWER-lower right-hand corner
Wires, cables, sheets, rods, and other materials manufactured
to gage or code numbers shall be specified by ________
________ indicating the diameter or thickness - THE CORRECT
ANSWER-linear dimensions
a 90° angle applies where centerlines and lines depicting
features are... - THE CORRECT ANSWER-shown on a drawing at right
angles by basic dimensioning and no angle is specified
Dimensions and tolerances apply only at the drawing level
where... - THE CORRECT ANSWER-they are specified
MULTIPLE CHOICE QUESTIONS AND
DETAILED SOLVED SOLUTIONS
ALREADY GRADED A+ AND 100% PASS
GUARANTEE (BRAND NEW
EDITION!!!!!!)
circles are typically dimensioned as - THE CORRECT ANSWER-
diameters
arcs are dimensioned as - THE CORRECT ANSWER-radii
T/F you should give dimensions between holes vs dimensioning
the holes from the end of the part - THE CORRECT ANSWER-True
Baseline Dimensioning - THE CORRECT ANSWER-all of the
dimensions in a given direction originate from a base or datum
(frequently used for CNC machines)
Chain Dimensioning - THE CORRECT ANSWER-features are
dimensioned relative to one another (used when a part function
requires that features be related to one another)
T/F chain dimensioning is often preferred over baseline - THE
CORRECT ANSWER-False, Baseline dimensioning is prefrred
,Chain dimensioning usually yields the _______ accumulation
of tolerance between features,where the maximum distance
between features is... - THE CORRECT ANSWER-largest; equal to the
sum of the intermediate distances
dimension only to _______ or _______ lines - THE CORRECT
ANSWER-visible; solid
Dimension lines also should be at least _____ ___ from any
view, helping to avoid clutter. - THE CORRECT ANSWER-10 mm
When dimensions are placed outside other dimensions, there
should be at least ___ ___ between dimension lines - THE
CORRECT ANSWER-6 mm
When dimensioning a visible gap of at least ___ ___ should be
between extension lines and object geometry - THE CORRECT
ANSWER-1 mm
when dimensioning, extension lines should extend ___-___
___ past their corresponding dimension line - THE CORRECT
ANSWER-2-3 mm
Chamfersy are dimensioned by - THE CORRECT ANSWER-giving a
length from the end of the part and an angle or by specifying
two distances
, |___| represents what on a drawing? - THE CORRECT ANSWER-
counterbore
\/ represents what on a drawing? - THE CORRECT ANSWER-
countersink
a line with an arrow pointing down represents what on a
drawing? - THE CORRECT ANSWER-specifying depth
Unless otherwise specified, all geometric tolerances apply for... -
THE CORRECT ANSWER-full depth, length, and width of the feature
notes typically appear in the _____________________
corner of a drawing and apply to the whole drawing - THE CORRECT
ANSWER-lower right-hand corner
Wires, cables, sheets, rods, and other materials manufactured
to gage or code numbers shall be specified by ________
________ indicating the diameter or thickness - THE CORRECT
ANSWER-linear dimensions
a 90° angle applies where centerlines and lines depicting
features are... - THE CORRECT ANSWER-shown on a drawing at right
angles by basic dimensioning and no angle is specified
Dimensions and tolerances apply only at the drawing level
where... - THE CORRECT ANSWER-they are specified
