BMW DRIVETRAIN MASTER ELITE ASE
EXAM | ENGINE, TRANSMISSION, AND
PERFORMANCE EXAM | 100%
CORRECTLY ANSWERED AND RATED
A+ | 2025/2026 GUIDE
What is the role of the auxiliary transmission fluid pump in automatic
transmissions?
- Correct Answer - Diagnose the auxiliary transmission fluid pump(s)
and/or pressure accumulator found in stop/start adapted automatic
transmissions.
What is the purpose of road testing a vehicle for electronic system
problems?
- Correct Answer - To verify electronic system problems based on the
driver's concern and research vehicle service history.
What equipment is used to diagnose electronic transmission control
systems?
- Correct Answer - Appropriate test equipment, service information,
technical service bulletins, and schematics.
,What should be verified when checking the vehicle's charging system?
- Correct Answer - Verify proper operation of the charging system, check
battery type, size, ratings, sensors, connections, and power/ground
circuits.
How can you differentiate between various vehicle system problems?
- Correct Answer - Differentiate between engine performance,
powertrain, transfer case, or other vehicle systems, and
transmission/transaxle-related problems.
What is the significance of using a scan tool in diagnosing electronic
systems?
- Correct Answer - To diagnose electronic systems, interpret readings,
and determine necessary action.
What procedures may be performed using a diagnostic scan tool?
- Correct Answer - Access, verify, and update software calibration
settings and perform control module re-learn and adaptation procedures.
What components are inspected and adjusted in in-vehicle transmission
maintenance?
- Correct Answer - Manual valve shift linkage, cables, bushings, and
transmission range sensor/switch.
, What should be checked regarding the engine cooling system during
transmission maintenance?
- Correct Answer - Check the condition and operation of the engine
cooling system, including the transmission cooler/warmer and related
components.
What is involved in off-vehicle transmission repair?
- Correct Answer - Remove and install transmission/transaxle, inspect
rear crankshaft seal, dowel pins, and mating surfaces.
What should be inspected when installing a torque converter?
- Correct Answer - Inspect converter flex plate, attaching bolts, pilot
engagement, and pump drive surfaces.
What maintenance is performed on transmission fluid coolers?
- Correct Answer - Inspect, test, flush, or replace the transmission fluid
cooler/warmer, thermostat, thermal bypass valve(s), and lines.
What is the importance of torque specifications during transmission
maintenance?
- Correct Answer - Torque valve body fasteners to specification using the
proper sequence.
EXAM | ENGINE, TRANSMISSION, AND
PERFORMANCE EXAM | 100%
CORRECTLY ANSWERED AND RATED
A+ | 2025/2026 GUIDE
What is the role of the auxiliary transmission fluid pump in automatic
transmissions?
- Correct Answer - Diagnose the auxiliary transmission fluid pump(s)
and/or pressure accumulator found in stop/start adapted automatic
transmissions.
What is the purpose of road testing a vehicle for electronic system
problems?
- Correct Answer - To verify electronic system problems based on the
driver's concern and research vehicle service history.
What equipment is used to diagnose electronic transmission control
systems?
- Correct Answer - Appropriate test equipment, service information,
technical service bulletins, and schematics.
,What should be verified when checking the vehicle's charging system?
- Correct Answer - Verify proper operation of the charging system, check
battery type, size, ratings, sensors, connections, and power/ground
circuits.
How can you differentiate between various vehicle system problems?
- Correct Answer - Differentiate between engine performance,
powertrain, transfer case, or other vehicle systems, and
transmission/transaxle-related problems.
What is the significance of using a scan tool in diagnosing electronic
systems?
- Correct Answer - To diagnose electronic systems, interpret readings,
and determine necessary action.
What procedures may be performed using a diagnostic scan tool?
- Correct Answer - Access, verify, and update software calibration
settings and perform control module re-learn and adaptation procedures.
What components are inspected and adjusted in in-vehicle transmission
maintenance?
- Correct Answer - Manual valve shift linkage, cables, bushings, and
transmission range sensor/switch.
, What should be checked regarding the engine cooling system during
transmission maintenance?
- Correct Answer - Check the condition and operation of the engine
cooling system, including the transmission cooler/warmer and related
components.
What is involved in off-vehicle transmission repair?
- Correct Answer - Remove and install transmission/transaxle, inspect
rear crankshaft seal, dowel pins, and mating surfaces.
What should be inspected when installing a torque converter?
- Correct Answer - Inspect converter flex plate, attaching bolts, pilot
engagement, and pump drive surfaces.
What maintenance is performed on transmission fluid coolers?
- Correct Answer - Inspect, test, flush, or replace the transmission fluid
cooler/warmer, thermostat, thermal bypass valve(s), and lines.
What is the importance of torque specifications during transmission
maintenance?
- Correct Answer - Torque valve body fasteners to specification using the
proper sequence.
