BMW ASSOCIATE LEVEL ASE EXAM |
PRACTICE QUESTIONS AND ANSWERS
RATED A+ | 100% CORRECT | 2025/2026
GUIDE
CPO inspections require a minimum tread depth of 3 mm, as measured
from the lowest area in the tread. T or F?
- Correct Answer - False (from top of wear indicators)
A technician should consider which of the following questions for a
quality control process after performing service work to a vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above
- Correct Answer - All of the above
While performing a CPO inspection, a technician finds the car has an
aftermarket LED headlight installed. The technician should:
- Correct Answer - Fail the CPO inspection or replace the Headlighits
What is the importance of having the engine at operating temperature
when performing an oil service?
Drains oil faster
Removes more contaminants
, The repair instructions say to do it
All of the above
- Correct Answer - All of the above
What is the minimum road test distance for a CPO inspection?
- Correct Answer - 5 miles
Regarding BMW wiper service mode.
Technician A says that on F and G series vehicles it is necessary to
place the wipers in service mode prior to removing the wiper blades.
Technician B says that on a G series vehicle; activate the vehicle by
pressing the start/stop button. Then deactivate the vehicle by pressing
the start/stop button again within 3 seconds. Then hold the wiper stalk in
the up position.
Who is correct?
- Correct Answer - A only
Engine oil Top-up services may be reimbursed under the terms of the
BMW Maintenance Program when it is "active" on the vehicle.
- Correct Answer - True
During a CPO inspection, a front brake pad measurement is taken of
4mm on the left inner pad and 7mm on the left outer pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed
specifications.
Who is correct?
- Correct Answer - Neither A or B
PRACTICE QUESTIONS AND ANSWERS
RATED A+ | 100% CORRECT | 2025/2026
GUIDE
CPO inspections require a minimum tread depth of 3 mm, as measured
from the lowest area in the tread. T or F?
- Correct Answer - False (from top of wear indicators)
A technician should consider which of the following questions for a
quality control process after performing service work to a vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above
- Correct Answer - All of the above
While performing a CPO inspection, a technician finds the car has an
aftermarket LED headlight installed. The technician should:
- Correct Answer - Fail the CPO inspection or replace the Headlighits
What is the importance of having the engine at operating temperature
when performing an oil service?
Drains oil faster
Removes more contaminants
, The repair instructions say to do it
All of the above
- Correct Answer - All of the above
What is the minimum road test distance for a CPO inspection?
- Correct Answer - 5 miles
Regarding BMW wiper service mode.
Technician A says that on F and G series vehicles it is necessary to
place the wipers in service mode prior to removing the wiper blades.
Technician B says that on a G series vehicle; activate the vehicle by
pressing the start/stop button. Then deactivate the vehicle by pressing
the start/stop button again within 3 seconds. Then hold the wiper stalk in
the up position.
Who is correct?
- Correct Answer - A only
Engine oil Top-up services may be reimbursed under the terms of the
BMW Maintenance Program when it is "active" on the vehicle.
- Correct Answer - True
During a CPO inspection, a front brake pad measurement is taken of
4mm on the left inner pad and 7mm on the left outer pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed
specifications.
Who is correct?
- Correct Answer - Neither A or B
