ASE Brakes A5 Test ( Exam 1 ), ASE A5 Brakes, ASE
Brakes A5 ( Exam 3 ), ASE Brakes A5 Test ( Exam 2
) | 2025 UPDATE!!
Save
Terms in this set (243)
A drum is chattering on A : failure to install the dampening belt
the brake lathe. This could
be a result of why : a missing dampening belt could cause the drum
to vibrate while on the lathe. this vibration can cause
a. failure to install the the drum to bounce on the cutting tip and make a
dampening belt chattering noise
b. cutting too slowly
c. dull cutting blades
d. cutting speed too fast
A vehicle equipped with a C : low power steering fluid
hydro-boost brake system
has a hard pedal with little why : low power steering fluid can cause the booster
braking action. Which of to provide very little if any boost
the following could be the
cause?
a. low brake fluid
b. air in the brake fluid
c. low power steering fluid
d. an overtightened power
steering belt
,Which of the following D : missing clips
could cause excessive
noise braking? why : missing anti-rattle clips could cause excessive
noise while braking
a. worn wheel cylinders
b. worn caliper pistons
c. seized caliper slides
d. missing clips
A vehicle equipped with a C : scan tool
"hill holding" option has an
ABS code. Which tool why : a scan tool or oscilloscope can be used to test a
would most likely be used signal from a digital when speed sensor
to check the wheel speed
sensor?
a. AC volt meter
b. Ohm meter
c. Scan tool
d. Ammeter
The brake system has a C : a bypassing master cylinder
soft, sinking pedal with the
engine running. The brake why : a bypassing master cylinder would cause a low
fluid level is at the correct pedal and would not cause a loss of fluid
height. Which of the
following could be the
cause?
a. a restricted vacuum
hose
b. a leaking master
cylinder
c. a bypassing master
cylinder
d. a stuck open vacuum
check valve
,Technician A says the pins D : neither A OR B
should be driven in with a
brass hammer. Technician why : neither technician is correct. this style of pin
B says the pins should be should be installed with a torx or hex head socket
lubricated with brake fluid.
Who is correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A OR B
Technician A says a hydro- A : only A
boost system can use the
power steering pump to why : only tech A is correct. a hydro-boost system
operate the booster. uses hydraulic pressure to create boost
Technician B says a hydro-
boost system can use
engine vacuum to operate
the booster. Who is
correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A & B
A disc brake caliper is D : worn brake pads
dragging. All of the
following could be the why : worn brake pads will not cause the brakes to
cause EXCEPT drag
a. binding pins
b. sticking piston
c. binding caliper
d. worn brake pads
, Which operation is being C : master cylinder bleeding
performed in the
illustration? ( pg. 48 ) why : the master cylinder is being bleed prior to
installation
a. wheel cylinder bleeding
b. brake caliper bleeding
c. master cylinder
bleeding
d. master cylinder
pressure test
The rear wheels of a front A : A only
wheel drive car lockup
during heavy breaking. why : tech A is correct. a faulty proportioning valve
Technician A says this could cause the pressure to the rear wheels to be too
could be cause by faulty high and lock the wheels during hard braking
proportioning valve.
Technician B says this
could be caused by a
faulty brake booster. Who
is correct?
a. A only
b. B only
c. Both A & B
d. Neither A or B
There is a loud growling B : worn wheel bearing
noise only when the
vehicle is steered to the why : this is a typical wheel bearing noise
right while driving. Which
of the following could be
the cause?
a. work left front brakes
b. worn wheel bearing
c. worn right front brakes
d. sticking brake caliper
Brakes A5 ( Exam 3 ), ASE Brakes A5 Test ( Exam 2
) | 2025 UPDATE!!
Save
Terms in this set (243)
A drum is chattering on A : failure to install the dampening belt
the brake lathe. This could
be a result of why : a missing dampening belt could cause the drum
to vibrate while on the lathe. this vibration can cause
a. failure to install the the drum to bounce on the cutting tip and make a
dampening belt chattering noise
b. cutting too slowly
c. dull cutting blades
d. cutting speed too fast
A vehicle equipped with a C : low power steering fluid
hydro-boost brake system
has a hard pedal with little why : low power steering fluid can cause the booster
braking action. Which of to provide very little if any boost
the following could be the
cause?
a. low brake fluid
b. air in the brake fluid
c. low power steering fluid
d. an overtightened power
steering belt
,Which of the following D : missing clips
could cause excessive
noise braking? why : missing anti-rattle clips could cause excessive
noise while braking
a. worn wheel cylinders
b. worn caliper pistons
c. seized caliper slides
d. missing clips
A vehicle equipped with a C : scan tool
"hill holding" option has an
ABS code. Which tool why : a scan tool or oscilloscope can be used to test a
would most likely be used signal from a digital when speed sensor
to check the wheel speed
sensor?
a. AC volt meter
b. Ohm meter
c. Scan tool
d. Ammeter
The brake system has a C : a bypassing master cylinder
soft, sinking pedal with the
engine running. The brake why : a bypassing master cylinder would cause a low
fluid level is at the correct pedal and would not cause a loss of fluid
height. Which of the
following could be the
cause?
a. a restricted vacuum
hose
b. a leaking master
cylinder
c. a bypassing master
cylinder
d. a stuck open vacuum
check valve
,Technician A says the pins D : neither A OR B
should be driven in with a
brass hammer. Technician why : neither technician is correct. this style of pin
B says the pins should be should be installed with a torx or hex head socket
lubricated with brake fluid.
Who is correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A OR B
Technician A says a hydro- A : only A
boost system can use the
power steering pump to why : only tech A is correct. a hydro-boost system
operate the booster. uses hydraulic pressure to create boost
Technician B says a hydro-
boost system can use
engine vacuum to operate
the booster. Who is
correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A & B
A disc brake caliper is D : worn brake pads
dragging. All of the
following could be the why : worn brake pads will not cause the brakes to
cause EXCEPT drag
a. binding pins
b. sticking piston
c. binding caliper
d. worn brake pads
, Which operation is being C : master cylinder bleeding
performed in the
illustration? ( pg. 48 ) why : the master cylinder is being bleed prior to
installation
a. wheel cylinder bleeding
b. brake caliper bleeding
c. master cylinder
bleeding
d. master cylinder
pressure test
The rear wheels of a front A : A only
wheel drive car lockup
during heavy breaking. why : tech A is correct. a faulty proportioning valve
Technician A says this could cause the pressure to the rear wheels to be too
could be cause by faulty high and lock the wheels during hard braking
proportioning valve.
Technician B says this
could be caused by a
faulty brake booster. Who
is correct?
a. A only
b. B only
c. Both A & B
d. Neither A or B
There is a loud growling B : worn wheel bearing
noise only when the
vehicle is steered to the why : this is a typical wheel bearing noise
right while driving. Which
of the following could be
the cause?
a. work left front brakes
b. worn wheel bearing
c. worn right front brakes
d. sticking brake caliper
