TTT1 Study guide with all Correct & 100% Verified
Answers |Actual Complete Exam |Already Graded A+
Who is the third party group that approves and endorses standards? ✔Correct Answer-American
National Standards Institute
What term is used to describe the documents written by members, or peers, in the industry?
✔Correct Answer-Standards
A company's health, safety and environment policy should be a combination of labor regulations
and ? ✔Correct Answer-Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the acts
general clause? ✔Correct Answer-Employer
On a job site who should be involved in the JHA process? ✔Correct Answer-The Whole Crew
What does the Term SOW stand for? ✔Correct Answer-Scope Of Work
The letters JHA stand for what ? ✔Correct Answer-Job Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? ✔Correct
Answer-3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall does
the case need to by to have the correct slope? ✔Correct Answer-4
Work boots with ankle support are recommended for all work sites? ✔Correct Answer-True
What do the letters PPE stand for ? ✔Correct Answer-Personal Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? ✔Correct Answer-Senses a short circuit,
prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? ✔Correct Answer-Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection to your
anchorage be placed?extend? ✔Correct Answer-Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? ✔Correct
Answer-Nine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull out
distance? ✔Correct Answer-Four feey
What is the minimum force that a work positioning system anchorage must be able to withstand?
✔Correct Answer-Two times the arresting force of 3000lbs
, What minimum force must a non-engineered anchor be able to withstand for fall protection use?
✔Correct Answer-5,000 lbs
When working, how often should fall protection equipment be inspected ? ✔Correct Answer-Daily
before each use
According to the applicable industry standard, what is the minimum height from a lower surface or
ground where fall protection must be used? ✔Correct Answer-Six feet
How many pounds force is one kilo Newton(kN) ✔Correct Answer-225
What are the four most common types of towers used to support telecommunications antennas?
✔Correct Answer-Guyed towers, self-support towers, monopoles, and non- standard
What identifies a self-support tower? ✔Correct Answer-Horizontal member
What is not a component on a guyed tower? ✔Correct Answer-Gin pole
What is the purpose of a turnbuckle when working with guy wires? ✔Correct Answer-Adjusts the
tension
Which government organization regulates tower lighting ? ✔Correct Answer-FAA
When completing tower demolition, what must you have in place before you start the job?
✔Correct Answer-Demolition permit
When completing the visual inspection of a foundation, what is one of the key items to look for?
✔Correct Answer-Cracks
What term identifies a monopole component? ✔Correct Answer-Base flange
According to the manufacturers specifications, what is the minimum number of ground kits installed
on a single Run? ✔Correct Answer-Three
What type of antenna is used to transmit signal from tower to tower? ✔Correct Answer-
Microwave dish
Where should a coax ground be placed vertically in relation to the hoisting grip? ✔Correct Answer-
Above it
When using tape and butyl to weatherproof a ground kit, what is a critical step in this process ?
✔Correct Answer-Cut the tape when terminator
When inspecting a wire rope diameter the actual diameter is slightly larger then the specific
diameter ? ✔Correct Answer-True
What does FS stand for in rigging applications ? ✔Correct Answer-Factor or safety
The outer sheath of synthetic endless sling is part of the slings strength? ✔Correct Answer-False
What does BS stand for in rigging applications ? ✔Correct Answer-Breaking Strength
Answers |Actual Complete Exam |Already Graded A+
Who is the third party group that approves and endorses standards? ✔Correct Answer-American
National Standards Institute
What term is used to describe the documents written by members, or peers, in the industry?
✔Correct Answer-Standards
A company's health, safety and environment policy should be a combination of labor regulations
and ? ✔Correct Answer-Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the acts
general clause? ✔Correct Answer-Employer
On a job site who should be involved in the JHA process? ✔Correct Answer-The Whole Crew
What does the Term SOW stand for? ✔Correct Answer-Scope Of Work
The letters JHA stand for what ? ✔Correct Answer-Job Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? ✔Correct
Answer-3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall does
the case need to by to have the correct slope? ✔Correct Answer-4
Work boots with ankle support are recommended for all work sites? ✔Correct Answer-True
What do the letters PPE stand for ? ✔Correct Answer-Personal Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? ✔Correct Answer-Senses a short circuit,
prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? ✔Correct Answer-Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection to your
anchorage be placed?extend? ✔Correct Answer-Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? ✔Correct
Answer-Nine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull out
distance? ✔Correct Answer-Four feey
What is the minimum force that a work positioning system anchorage must be able to withstand?
✔Correct Answer-Two times the arresting force of 3000lbs
, What minimum force must a non-engineered anchor be able to withstand for fall protection use?
✔Correct Answer-5,000 lbs
When working, how often should fall protection equipment be inspected ? ✔Correct Answer-Daily
before each use
According to the applicable industry standard, what is the minimum height from a lower surface or
ground where fall protection must be used? ✔Correct Answer-Six feet
How many pounds force is one kilo Newton(kN) ✔Correct Answer-225
What are the four most common types of towers used to support telecommunications antennas?
✔Correct Answer-Guyed towers, self-support towers, monopoles, and non- standard
What identifies a self-support tower? ✔Correct Answer-Horizontal member
What is not a component on a guyed tower? ✔Correct Answer-Gin pole
What is the purpose of a turnbuckle when working with guy wires? ✔Correct Answer-Adjusts the
tension
Which government organization regulates tower lighting ? ✔Correct Answer-FAA
When completing tower demolition, what must you have in place before you start the job?
✔Correct Answer-Demolition permit
When completing the visual inspection of a foundation, what is one of the key items to look for?
✔Correct Answer-Cracks
What term identifies a monopole component? ✔Correct Answer-Base flange
According to the manufacturers specifications, what is the minimum number of ground kits installed
on a single Run? ✔Correct Answer-Three
What type of antenna is used to transmit signal from tower to tower? ✔Correct Answer-
Microwave dish
Where should a coax ground be placed vertically in relation to the hoisting grip? ✔Correct Answer-
Above it
When using tape and butyl to weatherproof a ground kit, what is a critical step in this process ?
✔Correct Answer-Cut the tape when terminator
When inspecting a wire rope diameter the actual diameter is slightly larger then the specific
diameter ? ✔Correct Answer-True
What does FS stand for in rigging applications ? ✔Correct Answer-Factor or safety
The outer sheath of synthetic endless sling is part of the slings strength? ✔Correct Answer-False
What does BS stand for in rigging applications ? ✔Correct Answer-Breaking Strength
