OECP QUESTIONS AND ANSWERS
What type of fire extinguisher is required on a crane - Answer -10BC
What should am operator do in the event of a power line contact - Answer -remain in
the machine unless fire or emergency
What is the minimum distance from a 200kv power line - Answer -20ft
Where must electrocution warnings be displayed - Answer -1 in the cab, 2 on the
outside
A boom angle indicator does not show what? - Answer -boom deflection
Hand signals must use what method? - Answer -standard method
An operator must obey a stop signal from who? - Answer -anyone
When using radio, telephone or electronic signals, receiving must be what? - Answer -
hands free
What must voice signals include? - Answer -function and direction, distance and speed,
function and stop
What is the minimum number of wraps on a drum - Answer -2
Most LMI's will not indicate - Answer -Levelness
If signals are interrupted the operator must do what? - Answer -stop safety
All directions must be given in the operator's what? - Answer -perspective
What are the ANSI/ASME audible signals - Answer -1 stop
2 forward
3 reverse
When can an LMI be used to weigh a load? - Answer -up to 75% of capacity at the
working radius
What is the correct procedure if an LMI fails? - Answer -use the load chart and the
boom angle unless not allowed by the manufacturer
What functions are disabled by a kick-out system? - Answer -hoist up, boom down,
telescope out
, Power lines are always presumed what? - Answer -energized
Travel distance on 2 way levers shall not exceed what? - Answer -14 inches from
neutral
Forces shall not be greater than what on a foot pedal? - Answer -50 pounds
A crane traveling at 15 mph must be able to stop in what distance? - Answer -32 feet
What does PCSA stand for? - Answer -power crane and shovel association
What is the safety factor for synthetic slings? - Answer -5 to 1
What is PS - Answer -plow steel
An annual inspection must be performed by a - Answer -qualified person
What is the construction rigging standard? - Answer -1926.251
What is the general industry rigging standard - Answer -1910.184
What is the general industry crane standard - Answer -1910.180
What is the construction crane standard - Answer -1926.1400 also known as subpart cc
What is the ANSI/ASME standard for construction crane - Answer -B30.5
What does ANSI stand for - Answer -American national standards institute
What does ASME stand for? - Answer -American society of mechanical engineers
What does CFR stand for - Answer -code of federal regulations
What part of the load charts does not show boom deflection - Answer -range diagram
A deduction should be made for an extension even when lifting from it?
True or false - Answer -false
What do asterisks signify on a load chart - Answer -structural capacity
The maximum list allowed for a land crane on a barge is? - Answer -5 degrees
Land cranes on a barge fall under what ANSI standard - Answer -B30.8
Dynamic movement of a barge can make lifts be what? - Answer -Unpredictable
What type of fire extinguisher is required on a crane - Answer -10BC
What should am operator do in the event of a power line contact - Answer -remain in
the machine unless fire or emergency
What is the minimum distance from a 200kv power line - Answer -20ft
Where must electrocution warnings be displayed - Answer -1 in the cab, 2 on the
outside
A boom angle indicator does not show what? - Answer -boom deflection
Hand signals must use what method? - Answer -standard method
An operator must obey a stop signal from who? - Answer -anyone
When using radio, telephone or electronic signals, receiving must be what? - Answer -
hands free
What must voice signals include? - Answer -function and direction, distance and speed,
function and stop
What is the minimum number of wraps on a drum - Answer -2
Most LMI's will not indicate - Answer -Levelness
If signals are interrupted the operator must do what? - Answer -stop safety
All directions must be given in the operator's what? - Answer -perspective
What are the ANSI/ASME audible signals - Answer -1 stop
2 forward
3 reverse
When can an LMI be used to weigh a load? - Answer -up to 75% of capacity at the
working radius
What is the correct procedure if an LMI fails? - Answer -use the load chart and the
boom angle unless not allowed by the manufacturer
What functions are disabled by a kick-out system? - Answer -hoist up, boom down,
telescope out
, Power lines are always presumed what? - Answer -energized
Travel distance on 2 way levers shall not exceed what? - Answer -14 inches from
neutral
Forces shall not be greater than what on a foot pedal? - Answer -50 pounds
A crane traveling at 15 mph must be able to stop in what distance? - Answer -32 feet
What does PCSA stand for? - Answer -power crane and shovel association
What is the safety factor for synthetic slings? - Answer -5 to 1
What is PS - Answer -plow steel
An annual inspection must be performed by a - Answer -qualified person
What is the construction rigging standard? - Answer -1926.251
What is the general industry rigging standard - Answer -1910.184
What is the general industry crane standard - Answer -1910.180
What is the construction crane standard - Answer -1926.1400 also known as subpart cc
What is the ANSI/ASME standard for construction crane - Answer -B30.5
What does ANSI stand for - Answer -American national standards institute
What does ASME stand for? - Answer -American society of mechanical engineers
What does CFR stand for - Answer -code of federal regulations
What part of the load charts does not show boom deflection - Answer -range diagram
A deduction should be made for an extension even when lifting from it?
True or false - Answer -false
What do asterisks signify on a load chart - Answer -structural capacity
The maximum list allowed for a land crane on a barge is? - Answer -5 degrees
Land cranes on a barge fall under what ANSI standard - Answer -B30.8
Dynamic movement of a barge can make lifts be what? - Answer -Unpredictable
