1|Page
ARDMS SPI Exam 2025 with the latest Version A
& B practice tests, study guides, and real-style
questions to boost your ultrasound certification
Description
ARDMS SPI exam 2025
ARDMS SPI latest version A and B
ARDMS SPI practice test 2025
ARDMS SPI study guide PDF
ARDMS SPI exam questions and answers
ARDMS SPI exam version A 2025
ARDMS SPI exam version B 2025
How to pass ARDMS SPI exam
ARDMS SPI practice exam free
VERSION A
,2|Page
Electronic focusing in transmit mode uses:
A) changeable lens.
B) curved element.
C) time delays to excite transducer elements.
D) high pulse repetition frequency. - ANSWER-C) time delays
to excite transducer elements.
5. Which transducer would you select for maximum
penetration?
A) 3 MHz curvilinear
B) 4 MHz phased array
C) 8 MHz linear phased array
D) 10 MHz tightly curved array - ANSWER-A) 3 MHz
curvilinear
6. The transducer component responsible for the timing and
order of the sequence is:
A) impedance matching layer.
B) beam former.
,3|Page
C) elevational resolution.
D) PZT. - ANSWER-B) beam former.
1. Which statement refers to the process of phasing?
A) Electronic beam steering
B) Acoustic lens
C) Electronic focusing
D) Mechanical movement of the probe - ANSWER-A) Electronic
beam steering
2. Which of the following is used to control elevational resolution
in a 2D transducer?
A) Bandwidth
B) Axial resolution
C) Lens
D) Beam former - ANSWER-D) Beam former
3. The conversion of an incident pressure wave into an electrical
signal is called:
, 4|Page
A) Snell's law.
B) piezoelectric effect.
C) Huygen's principle.
D) Curie effect. - ANSWER-B) piezoelectric effect.
7. An image is bright in the near field but darker in the far field.
Which process is responsible for this effect?
A) Propagation speed variations
B) Digital scan conversion
C) Acoustic attenuation
D) Refraction - ANSWER-C) Acoustic attenuation
8. If a calcification is present but there is not much shadowing,
what can you adjust to demonstrate more of the shadow?
A) Decrease line density
B) Adjust focal position to low
C) Increase frequency
D) Increase gain - ANSWER-C) Increase frequency
ARDMS SPI Exam 2025 with the latest Version A
& B practice tests, study guides, and real-style
questions to boost your ultrasound certification
Description
ARDMS SPI exam 2025
ARDMS SPI latest version A and B
ARDMS SPI practice test 2025
ARDMS SPI study guide PDF
ARDMS SPI exam questions and answers
ARDMS SPI exam version A 2025
ARDMS SPI exam version B 2025
How to pass ARDMS SPI exam
ARDMS SPI practice exam free
VERSION A
,2|Page
Electronic focusing in transmit mode uses:
A) changeable lens.
B) curved element.
C) time delays to excite transducer elements.
D) high pulse repetition frequency. - ANSWER-C) time delays
to excite transducer elements.
5. Which transducer would you select for maximum
penetration?
A) 3 MHz curvilinear
B) 4 MHz phased array
C) 8 MHz linear phased array
D) 10 MHz tightly curved array - ANSWER-A) 3 MHz
curvilinear
6. The transducer component responsible for the timing and
order of the sequence is:
A) impedance matching layer.
B) beam former.
,3|Page
C) elevational resolution.
D) PZT. - ANSWER-B) beam former.
1. Which statement refers to the process of phasing?
A) Electronic beam steering
B) Acoustic lens
C) Electronic focusing
D) Mechanical movement of the probe - ANSWER-A) Electronic
beam steering
2. Which of the following is used to control elevational resolution
in a 2D transducer?
A) Bandwidth
B) Axial resolution
C) Lens
D) Beam former - ANSWER-D) Beam former
3. The conversion of an incident pressure wave into an electrical
signal is called:
, 4|Page
A) Snell's law.
B) piezoelectric effect.
C) Huygen's principle.
D) Curie effect. - ANSWER-B) piezoelectric effect.
7. An image is bright in the near field but darker in the far field.
Which process is responsible for this effect?
A) Propagation speed variations
B) Digital scan conversion
C) Acoustic attenuation
D) Refraction - ANSWER-C) Acoustic attenuation
8. If a calcification is present but there is not much shadowing,
what can you adjust to demonstrate more of the shadow?
A) Decrease line density
B) Adjust focal position to low
C) Increase frequency
D) Increase gain - ANSWER-C) Increase frequency
